< Home

Example for Configuring IPv6 Addresses for Interfaces

Networking Requirements

In Figure 1, GE0/0/1 of SwitchA connects to GE0/0/1 of SwitchB. The two interfaces correspond to their VLANIF interfaces (VLANIF 100). You need to configure IPv6 addresses for the VLANIF interfaces and check the Layer 3 interconnection between the interfaces.

IPv6 addresses for the VLANIF interfaces are fc00:1::1/64 and fc00:1::2/64.

Figure 1 Networking diagram for configuring IPv6 addresses for interfaces

Configuration Roadmap

The configuration roadmap is as follows:

  1. Enable the IPv6 forwarding function on SwitchA and SwitchB.

  2. Configure IPv6 addresses for the interfaces.

Procedure

  1. Enable the IPv6 forwarding function on switches.

    # Configure SwitchA.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchA
    [SwitchA] ipv6

    # Configure SwitchB.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchB
    [SwitchB] ipv6

  2. Configure IPv6 addresses for the interfaces.

    # Configure SwitchA.

    [SwitchA] vlan 100
    [SwitchA-vlan100] quit
    [SwitchA] interface gigabitethernet 0/0/1
    [SwitchA-GigabitEthernet0/0/1] port link-type hybrid
    [SwitchA-GigabitEthernet0/0/1] port hybrid pvid vlan 100
    [SwitchA-GigabitEthernet0/0/1] port hybrid untagged vlan 100
    [SwitchA-GigabitEthernet0/0/1] quit
    [SwitchA] interface vlanif 100
    [SwitchA-Vlanif100] ipv6 enable
    [SwitchA-Vlanif100] ipv6 address fc00:1::1/64
    [SwitchA-Vlanif100] quit

    # Configure SwitchB.

    [SwitchB] vlan 100
    [SwitchB-vlan100] quit
    [SwitchB] interface gigabitethernet 0/0/1
    [SwitchB-GigabitEthernet0/0/1] port link-type hybrid
    [SwitchB-GigabitEthernet0/0/1] port hybrid pvid vlan 100
    [SwitchB-GigabitEthernet0/0/1] port hybrid untagged vlan 100
    [SwitchB-GigabitEthernet0/0/1] quit
    [SwitchB] interface vlanif 100
    [SwitchB-Vlanif100] ipv6 enable
    [SwitchB-Vlanif100] ipv6 address fc00:1::2/64
    [SwitchB-Vlanif100] quit

  3. Verify the configuration.

    # Check interface information on SwitchA.

    [SwitchA] display ipv6 interface vlanif 100
    Vlanif100 current state : UP
    IPv6 protocol current state : UP
    IPv6 is enabled, link-local address is FE80::218:20FF:FE00:83
      Global unicast address(es):
        FC00:1::1, subnet is FC00:1::/64
      Joined group address(es):
        FF02::1:FF00:1
        FF02::1:FF00:83
        FF02::2
        FF02::1
      MTU is 1500 bytes
      ND DAD is enabled, number of DAD attempts: 1
      ND reachable time is 30000 milliseconds
      ND retransmit interval is 1000 milliseconds
      ND stale time is 1200 seconds 
    

    # Check interface information on SwitchB.

    [SwitchB] display ipv6 interface vlanif 100
    Vlanif100 current state : UP
    IPv6 protocol current state : UP
    IPv6 is enabled, link-local address is FE80::2E0:FCFF:FE33:11
      Global unicast address(es):
        FC00:1::2, subnet is FC00:1::/64
      Joined group address(es):
        FF02::1:FF00:2
        FF02::1:FF33:11
        FF02::2
        FF02::1
      MTU is 1500 bytes
      ND DAD is enabled, number of DAD attempts: 1
      ND reachable time is 30000 milliseconds
      ND retransmit interval is 1000 milliseconds
      ND stale time is 1200 seconds 
    

    # Ping the IPv6 address of SwitchB from SwitchA.

    [SwitchA] ping ipv6 FC00:1::2
      PING FC00:1::2 : 56  data bytes, press CTRL_C to break
        Reply from FC00:1::2
        bytes=56 Sequence=1 hop limit=64  time = 12 ms
        Reply from FC00:1::2
        bytes=56 Sequence=2 hop limit=64  time = 3 ms
        Reply from FC00:1::2
        bytes=56 Sequence=3 hop limit=64  time = 3 ms
        Reply from FC00:1::2
        bytes=56 Sequence=4 hop limit=64  time = 3 ms
        Reply from FC00:1::2
        bytes=56 Sequence=5 hop limit=64  time = 3 ms
    
      --- FC00:1::2 ping statistics ---
        5 packet(s) transmitted
        5 packet(s) received
        0.00% packet loss
        round-trip min/avg/max = 3/4/12 ms
    

Configuration File

  • SwitchA configuration file

    #
    sysname SwitchA
    #
    ipv6
    #
    vlan batch 100
    #
    interface Vlanif100
     ipv6 enable
     ipv6 address FC00:1::1/64
    #
    interface GigabitEthernet0/0/1
     port link-type hybrid
     port hybrid pvid vlan 100
     port hybrid untagged vlan 100
    #
    return
  • SwitchB configuration file

    #
    sysname SwitchB
    #
    ipv6
    #
    vlan batch 100
    #
    interface Vlanif100
     ipv6 enable
     ipv6 address FC00:1::2/64
    #
    interface GigabitEthernet0/0/1
     port link-type hybrid
     port hybrid pvid vlan 100
     port hybrid untagged vlan 100
    #
    return
Copyright © Huawei Technologies Co., Ltd.
Copyright © Huawei Technologies Co., Ltd.
< Previous topic