display ap-group

Function

The display ap-group command displays configuration and reference information about an AP groups.

Format

display ap-group { all | name group-name }

Parameters

Parameter	Description	Value
all	Displays information about all AP groups.	-
name group-name	Displays information about a specified AP group.	The AP group must exist.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run the display ap-group command to view configuration and reference information about AP groups.

Example

# Display information about all AP groups.

<HUAWEI> display ap-group all
----------------------------------------------------------
Name                           APs
----------------------------------------------------------
default                        1
ap-group1                      0
----------------------------------------------------------
Total: 2

**Table 1** Description of the **display ap-group all** command output
Item	Description
Name	Name of an AP group.
APs	Number of APs in an AP group.

# Display information about the AP group default.

<HUAWEI> display ap-group name default
---------------------------------------------------------------------------------------
AP system profile          : default
Regulatory domain profile  : default
WIDS profile               : default
BLE profile                :  
AP location                : 
UUID                       :  
Domain name                : 
AP wired port profile
 Interface FE0             : default
 Interface FE1             : default
 Interface FE2             : default
 Interface FE3             : default
 Interface GE0             : default
......
 Interface GE27            : default
 Interface MultiGE0        : default
 Interface XGE0            : default
......
 Interface XGE4            : default
 Interface Eth-trunk0      : default
Radio 0              
 Radio 2.4G profile        : default
 Radio 5G profile          : default
 VAP profile               : 
 Mesh profile              :  
 WDS profile               :  
 Mesh whitelist profile    :  
 WDS whitelist profile     :  
 Location profile          :  
 Radio switch              : enable
 Channel                   : -
 Channel bandwidth         : 20mhz
 EIRP(dBm)                 : 127
 Antenna gain(dB)          : -
 Coverage distance(100 m)  : 3
 Work mode                 : normal
 Flexible radio switch     : on
 Radio frequency           : 2.4G
 Spectrum analysis         : disable
 WIDS device detect        : disable
 WIDS attack detect        : -
 WIDS contain switch       : disable
 Auto channel select       : enable
 Auto bandwidth select     : disable
 Auto transmit power select: enable
 Reference data-analysis   : enable
 Beacon switch             : enable
 CTS switch                : enable
 CTS delay time(us)        : none
Radio 1              
......
Radio 2              
......
Card 1              
 Card connect type         : -
 Wired port profile        : default
 Iot profile               :  
 Protocol Type             : -
 First Port                : -
 Extended Port             : - 
Card 2
......
Card usb              
 Iot profile               :  
 Protocol Type             : - 
 First Port                : - 
 Extended Port             : -

**Table 2** Description of the **display ap-group name** command output
Item	Description
AP system profile	AP system profile referenced by an AP group. To configure this parameter, run the ap-system-profile (AP group view and AP view) command.
Regulatory domain profile	Regulatory domain profile referenced by an AP group. To configure this parameter, run the regulatory-domain-profile command.
WIDS profile	WIDS profile referenced by an AP group. To configure this parameter, run the wids-profile (AP group view and AP view) command.
BLE profile	BLE profile referenced by an AP group. To configure this parameter, run the ble-profile (AP group view and AP view) command.
UUID	UUID of a BLE broadcast frame sent by the AP's built-in Bluetooth module. To configure this parameter, run the broadcasting-content (AP group view) command.
AP location	Installation position of an AP in the AP group. To configure this parameter, run the location command.
Domain name	Default domain name suffix of the AP. To configure this parameter, run the ip domain-name command.
AP wired port profile	AP wired port profile referenced by an AP group. To configure this parameter, run the wired-port-profile (AP group view and AP view) command.
Interface Interface-name	Interface name.
Radio 0/Radio 1/Radio 2	Radio ID.
Radio 2.4G profile	2G radio profile referenced by an AP group. To configure this parameter, run the radio-2g-profile command.
Radio 5G profile	5G radio profile referenced by an AP group. To configure this parameter, run the radio-5g-profile command.
VAP profile	VAP profile referenced by an AP group. The displayed format is "VAP ID:VAP profile name (service VLAN defined when binding to the VAP profile, single VLAN, or VLAN pool)." To configure this parameter, run the vap-profile command.
Mesh profile	Mesh profile referenced by an AP group. To configure this parameter, run the mesh-profile radio command.
WDS profile	WDS profile referenced by an AP group. To configure this parameter, run the wds-profile radio command.
Mesh whitelist profile	Mesh whitelist profile referenced by an AP group. To configure this parameter, run the mesh-whitelist-profile (AP group radio view or AP radio view) command.
WDS whitelist profile	WDS whitelist profile referenced by an AP group. To configure this parameter, run the wds-whitelist-profile (AP group radio view or AP radio view) command.
Location profile	Location profile referenced by an AP group. To configure this parameter, run the location-profile command.
Radio switch	Whether a radio is enabled. To configure this parameter, run the radio disable command.
Channel	Working channel of a radio. To configure this parameter, run the channel command.
Channel bandwidth	Working bandwidth of a radio. To configure this parameter, run the channel command.
EIRP(dBm)	Transmit power of a radio, in dBm. To configure this parameter, run the eirp command.
Antenna gain(dB)	Antenna gain of a radio, in dB. To configure this parameter, run the antenna-gain command.
Coverage distance(100 m)	Specifies the radio coverage distance parameter, in the unit of 100 m. To configure this parameter, run the coverage distance command.
Work mode	Working mode of a radio. To configure this parameter, run the work-mode command.
Flexible radio switch	Whether the DFA function of a radio is enabled. To configure this parameter, run the calibrate flexible-radio disable command.
Radio frequency	Working frequency band of a radio. To configure this parameter, run the frequency command.
Spectrum analysis	Whether spectrum analysis is enabled. To configure this parameter, run the spectrum-analysis enable command.
WIDS device detect	Whether wireless device detection is enabled. To configure this parameter, run the wids device detect enable command.
WIDS attack detect	Whether attack detection is enabled. To configure this parameter, run the wids attack detect command.
WIDS contain switch	Whether rogue device containment is enabled. To configure this parameter, run the wids contain enable command.
Auto channel select	Whether to enable automatic channel selection. To configure this parameter, run the calibrate auto-channel-select command.
Auto bandwidth select	Whether to enable automatic bandwidth selection. To configure this parameter, run the calibrate auto-bandwidth-selection command.
Auto transmit power select	Whether to enable automatic transmit power selection. To configure this parameter, run the calibrate auto-txpower-select command.
Reference data-analysis	Whether to enable big data calibration. To configure this parameter, run the calibrate reference data-analysis { disable \| enable } command.
Beacon switch	Whether RUs are enabled to send Beacon frames. To configure this parameter, run the beacon disable command.
CTS switch	Whether RUs are enabled to respond to STAs with CTS packets. To configure this parameter, run the cts disable command.
CTS delay time(us)	Delay time after which RUs respond to STAs with CTS packets. To configure this parameter, run the cts delay command.
Card 1/Card 2/Card 3/Card usb	IoT card.
Card connect type	Communication connection type between IoT cards and APs. To configure this parameter, run the card connect-type command.
Wired port profile	AP wired port profile referenced by an AP group. To configure this parameter, run the wired-port-profile (IoT card interface view) command.
Iot profile	Bound IoT profile. To configure this parameter, run the iot-profile (IoT card interface view) command.
Protocol Type	Communication protocol between the AP and host computer.
First Port	Source port for the first channel.
Extended Port	Source port for the extended channel.