The display default-parameter pim-sm command displays default configurations about PIM-SM. Even if PIM-SM parameters are modified, the display default-parameter pim-sm command still displays default parameter settings. Therefore, you can use this command to check which parameters on the device have been modified.
# Display default configurations about PIM-SM.
<HUAWEI> display default-parameter pim-sm PIM View Default Configurations: --------------------------------- Auto-rp listening enable: disabled Bsr-policy: disabled C-bsr admin-scope: disabled C-bsr global: disabled C-bsr group: none C-bsr hash-length: 30 C-bsr holdtime: 130 s C-bsr interval: 60 s C-bsr priority: 0 C-rp advertisement-interval: 60 s C-rp holdtime: 150 s C-rp priority: 0 Crp-policy: disabled Bsm semantic fragmentation: disabled Hello-option dr-priority: 1 Hello-option holdtime: 105 s Hello-option lan-delay: 500 ms Hello-option neighbor-tracking: disabled Hello-option override-interval: 2500 ms Holdtime assert: 180 s Holdtime join-prune: 210 s Probe-interval: 5 s Register-header-checksum: disabled Register-policy: disabled Register-suppression-timeout: 60 s Source-lifetime: 210 s Source-policy: disabled Spt-switch-threshold: disabled Ssm-policy: disabled Static-rp: disabled Hello periodic interval: 30 s Join-prune periodic interval: 60 s Timer spt-switch: 15 s Interface View Default Configurations: -------------------------------------- Pim bfd: disabled Pim bsr-boundary: disabled Pim hello-option dr-priority: 1 Pim hello-option holdtime: 105 s Pim hello-option lan-delay: 500 ms Pim hello-option neighbor-tracking: disabled Pim hello-option override-interval: 2500 ms Pim holdtime assert: 180 s Pim holdtime join-prune: 210 s Pim require-genid: disabled Pim silent: disabled Pim timer dr-switch-delay: disabled Pim hello periodic interval: 30 s Pim join-prune periodic interval: 60 s Pim triggered-hello-delay: 5 s Pim version: 2 Pim ipsec sa: disabled Pim join-policy: disabled Pim neighbor-policy: disabled
Item |
Description |
|---|---|
PIM View Default Configurations |
Default configurations in the PIM view. |
Auto-rp listening enable |
Whether the auo-RP listening function is enabled. The switch does not support this function. |
Bsr-policy |
Whether the valid address range of the BSR is set. This parameter is configured by the bsr-policy (IPv4) command. |
C-bsr admin-scope |
Whether the BSR administrative domain is configured. This parameter is configured by the c-bsr admin-scope command. |
C-bsr global |
Whether the C-BSR in the global domain is configured. This parameter is configured by the c-bsr global command. |
C-bsr group |
Whether the C-BSR in the BSR administrative domain is configured. This parameter is configured by the c-bsr group command. |
C-bsr hash-length |
Global hash mask length of the C-BSR. This parameter is configured by the c-bsr hash-length (IPv4) command. |
C-bsr holdtime |
Waiting time for the BSR to receive the Bootstrap message. This parameter is configured by the c-bsr holdtime (IPv4) command. |
C-bsr interval |
Interval for the BSR to send Bootstrap messages. This parameter is configured by the c-bsr interval (IPv4) command. |
C-bsr priority |
Global priority of the C-BSR. This parameter is configured by the c-bsr priority (IPv4) command. |
C-rp advertisement-interval |
Interval for the C-RP to send Advertisement messages. This parameter is configured by the c-rp advertisement-interval (IPv4) command. |
C-rp holdtime |
Waiting time for the BSR to receive the Advertisement message. This parameter is configured by the c-rp holdtime (IPv4) command. |
C-rp priority |
Global priority of the C-RP. This parameter is configured by the c-rp priority (IPv4) command. |
Crp-policy |
Whether the valid address range of the C-RP and the range of multicast groups that the C-RP serves are set. This parameter is configured by the crp-policy (IPv4) command. |
Bsm semantic fragmentation |
Whether the BSR fragmentation is enabled. This parameter is configured by the bsm semantic fragmentation (IPv4) command. |
Hello-option dr-priority |
Priority for DR election. This parameter is configured by the hello-option dr-priority (IPv4) command. |
Hello-option holdtime |
Time period for the neighbor to hold the reachable state, in seconds. This parameter is configured by the hello-option holdtime (IPv4) command. |
Hello-option lan-delay |
Delay in transmitting Prune messages at a shared network segment, in milliseconds. This parameter is configured by the hello-option lan-delay (IPv4) command. |
Hello-option neighbor-tracking |
Whether neighbor tracking is enabled. This parameter is configured by the hello-option neighbor-tracking (IPv4) command. |
Hello-option override-interval |
Interval for sending Prune Override messages, in milliseconds. This parameter is configured by the hello-option override-interval (IPv4) command. |
Holdtime assert |
Time period for holding the Assert state, in seconds. This parameter is configured by the holdtime assert (IPv4) command. |
Holdtime join-prune |
Time period for holding the Join or Prune state, in seconds. This parameter is configured by the holdtime join-prune (IPv4) command. |
Probe-interval |
Interval for sending Probe messages (empty Register messages) to the RP, in seconds. This parameter is configured by the probe-interval (IPv4) command. |
Register-header-checksum |
Whether calculating the checksum based on information in Register message header is required. This parameter is configured by the register-header-checksum command. |
Register-policy |
Whether the rule for filtering Register messages is configured. This parameter is configured by the register-policy (IPv4) command. |
Register-suppression-timeout |
Time period for holding the register-suppression state, in seconds. This parameter is configured by the register-suppression-timeout (IPv4) command. |
Source-lifetime |
Timeout period of an (S, G) entry, in seconds. This parameter is configured by the source-lifetime (IPv4) command. |
Source-policy |
Whether the rule for filtering multicast sources is configured. This parameter is configured by the source-policy (IPv4) command. |
Spt-switch-threshold |
Whether the threshold of the multicast packet rate that triggers the switch from the RPT to the SPT is configured. This parameter is configured by the spt-switch-threshold (IPv4) command. |
Ssm-policy |
Whether the SSM group address range is set. This parameter is configured by the ssm-policy (IPv4) command. |
Static-rp |
Whether the static RP is configured. This parameter is configured by the static-rp (IPv4) command. |
Hello periodic interval |
Interval for sending Hello messages, in seconds. This parameter is configured by the timer hello (IPv4) command. |
Join-prune periodic interval |
Interval for sending Join/Prune messages, in seconds. This parameter is configured by the timer join-prune (IPv4) command. |
Timer spt-switch |
Whether the interval for checking whether the multicast packet rate exceeds the threshold before the switchover from RPT to SPT is configured, in seconds. This parameter is configured by the timer spt-switch (IPv4) command. |
Interface View Default Configurations |
Default configurations in the interface view. |
Pim bfd |
Whether PIM BFD is enabled on the interface. This parameter is configured by the pim bfd enable command. |
Pim bsr-boundary |
Whether the PIM boundary is configured on the interface. This parameter is configured by the pim bsr-boundary command. |
Pim hello-option dr-priority |
Priority for DR election on the interface. This parameter is configured by the pim hello-option dr-priority command. |
Pim hello-option holdtime |
Time period for the neighbor on the interface to hold the reachable state, in seconds. This parameter is configured by the pim hello-option holdtime command. |
Pim hello-option lan-delay |
Delay in transmitting Prune messages at a shared network segment on the interface, in milliseconds. This parameter is configured by the pim hello-option lan-delay command. |
Pim hello-option neighbor-tracking |
Whether neighbor tracking is enabled on the interface. This parameter is configured by the pim hello-option neighbor-tracking command. |
Pim hello-option override-interval |
Interval for the interface to send Prune Override messages, in milliseconds. This parameter is configured by the pim hello-option override-interval command. |
Pim holdtime assert |
Time period for the interface to hold the Assert state, in seconds. This parameter is configured by the pim holdtime assert command. |
Pim holdtime join-prune |
Time period for the interface to hold the Join or Prune state, in seconds. This parameter is configured by the pim holdtime join-prune command. |
Pim require-genid |
Whether the received Hello message is required to carry the Generation ID. This parameter is configured by the pim require-genid command. |
Pim silent |
Whether PIM Silent is enabled on the interface. This parameter is configured by the pim silent command. |
Pim timer dr-switch-delay |
Whether the DR switch delay is set on the interface. This parameter is configured by the pim timer dr-switch-delay command. |
Pim hello periodic interval |
Interval for the interface to send Hello messages, in seconds. This parameter is configured by the pim timer hello command. |
Pim join-prune periodic interval |
Interval for the interface to send Join/Prune messages, in seconds. This parameter is configured by the pim timer join-prune command. |
Pim triggered-hello-delay |
Maximum delay for the interface to send Hello messages, in seconds. This parameter is configured by the pim triggered-hello-delay command. |
Pim version |
Version of PIM enabled on the interface. |
Pim ipsec sa |
Whether PIM IPSec is enabled on the interface. This parameter is configured by the pim ipsec sa command. |
Pim join-policy |
Whether the join-policy is configured on the interface. This parameter is configured by the pim join-policy command. |
Pim neighbor-policy |
Whether the neighbor-policy is configured on the interface. This parameter is configured by the pim neighbor-policy command. |