display mpls rsvp-te interface

Function

The display mpls rsvp-te interface command displays the RSVP-TE configurations on an interface.

Format

display mpls rsvp-te interface [ interface-type interface-number ]

Parameters

Parameter	Description	Value
interface-type interface-number	Specifies the interface type and number. interface-type specifies the interface type. interface-number specifies the interface number.	-

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

If the type and number of an interface is not specified, the display mpls rsvp-te interface command displays the RSVP-TE information of all RSVP TE-enabled interfaces.

Example

# Display information about RSVP-TE of a specified interface.

<HUAWEI> display mpls rsvp-te interface vlanif 100
Interface: Vlanif100                                                 
 Interface Address: 11.11.11.11                                                 
 Interface state: UP                   Interface Index: 0x4                     
 Total-BW: 0                           Used-BW: 0                               
 Hello configured: NO                  Num of Neighbors: 0                      
 SRefresh feature: DISABLE             SRefresh Interval: 30 sec                
 Mpls Mtu: 1500                        Retransmit Interval: 5000 msec           
 Increment Value: 1                                                             
 Authentication: DISABLE                                                        
 Bfd Enabled: DISABLE                  Bfd Min-Tx: 400                          
 Bfd Min-Rx: 300                       Bfd Detect-Multi: 4

**Table 1** Description of the display mpls rsvp-te interface command output
Item	Description
Interface	Name of a tunnel interface.
Interface Address	IP address of an interface.
Interface state	Interface status: UP DOWN
Interface Index	Index of an interface.
Total-BW	Total available bandwidth of an interface, in kbit/s.
Used-BW	Total bandwidth of an interface in use, in kbit/s.
Hello configured	Whether the Hello feature is configured on an interface: YES: indicates that the Hello feature is configured. NO: indicates that the Hello feature is not configured.
Num of Neighbors	Number of neighbor devices of the local node.
SRefresh feature	Whether the Srefresh feature is enabled. To enable the Srefresh feature, run the mpls rsvp-te srefresh command in the interface view.
SRefresh Interval	Value of the Srefresh timer, in seconds. To specify the value of the Srefresh timer, run the mpls rsvp-te timer refresh command.
Mpls Mtu	MTU value used in MPLS forwarding.
Retransmit Interval	Value of the Retransmit timer, in milliseconds. To specify the value of the Retransmit timer, run the mpls rsvp-te timer retransmission command.
Increment Value	Retransmission increment. To specify the retransmission increment, run the mpls rsvp-te timer retransmission command.
Authentication	Whether the authentication function is enabled: ENABLE: indicates that the authentication function is enabled. DISABLE: indicates that the authentication function is disabled. To enable the authentication function, run the mpls rsvp-te authentication command.
Bfd Enabled	Whether BFD for RSVP is enabled on the interface: ENABLE: indicates that BFD for RSVP is enabled on the interface. DISABLE: indicates that BFD for RSVP is not enabled on the interface. To enable BFD for RSVP, run the mpls rsvp-te bfd enable command.
Bfd Min-Tx	Local interval at which BFD packets are sent, in milliseconds. To specify the local minimum interval at which BFD packets are sent, run the mpls rsvp-te bfd command.
Bfd Min-Rx	Local interval at which BFD packets are received, in milliseconds. To specify the local minimum interval at which BFD packets are received, run the mpls rsvp-te bfd command.
Bfd Detect-Multi	Local BFD detection multiplier. To specify the local BFD detection multiplier, run the mpls rsvp-te bfd command.