display poe information

Function

The display poe information command displays PoE running information about the device.

Format

display poe information [ slot slot-id ]

Parameters

Parameter	Description	Value
slot slot-id	Displays the PoE running information in a specified slot ID. If this parameter is not specified, the PoE information about all device is displayed.	The value depends on the device configuration.

Parameter

Description

Value

slot slot-id

Displays the PoE running information in a specified slot ID.

If this parameter is not specified, the PoE information about all device is displayed.

The value depends on the device configuration.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

This command displays information including the maximum output power set by the user, current power consumption, peak power consumption, and power management mode.

Example

# Display the PoE running information about the device. (The actual output information may differ from the following information.)

<HUAWEI> display poe information
PSE Information of slot 0:
    User Set Max Power(mW)     : 739200
    PoE Power Supply(mW)       : 369600
    Available Total Power(mW)  : 369600
    Total Power Consumption(mW): 0
    Power Peak Value(mW)       : 0
    Power-Management Mode      : auto
    Power High Inrush          : disable 
    Port Index Priority        : enable

<HUAWEI> display poe information
PSE Information of slot 0:
MCU 1:
    User Set Max Power(mW)     : 739200
    PoE Power Supply(mW)       : 369600
    Available Total Power(mW)  : 369600
    Total Power Consumption(mW): 0
    Power Peak Value(mW)       : 0
    Power-Management Mode      : auto
    Power High Inrush          : disable 
    Port Index Priority        : enable
MCU 2: 
    User Set Max Power(mW)     : 739200
    PoE Power Supply(mW)       : 369600
    Available Total Power(mW)  : 369600
    Total Power Consumption(mW): 0
    Power Peak Value(mW)       : 0
    Power-Management Mode      : auto
    Power High Inrush          : disable 
    Port Index Priority        : enable

**Table 1** Description of the **display poe information** command output
Item	Description
User Set Max Power(mW)	Maximum output power set by the user. To set the value, run the poe max-power command. When the value is not set using the command, this field displays the maximum output power that can be provided by the device.
PoE Power Supply(mW)	PoE power supply, which is determined by the PoE power module configured on the device.
Available Total Power(mW)	Total available power. NOTE: On the S5720I-6X-PWH-SI-AC switch, the total available power includes the power of two 12 V DC outputs and one 24 V AC output. No command is available to view the 12 V DC and 24 V AC output power. On the S5720I-10X-PWH-SI-AC switch, the total available power includes the power of two 12 V DC outputs and one 24 V AC output. To view the DC output power, run the display device dc-output information command.
Total Power Consumption(mW)	Total output power.
Power Peak Value(mW)	Peak value of the output power.
Power-Management Mode	Power management mode, including auto and manual modes. To set the mode, run the poe power-management command.
Power High Inrush	State of power high inrush function, including enabled and disabled state. By default, the power high inrush function is in disabled state. To set the state, run the poe high-inrush enable command.
Port Index Priority	Whether the device is enabled to power on or off PDs connected to interfaces based on the interface numbers. By default, a device powers on or off PDs connected to interfaces based on the interface numbers. To configure this parameter, run the poe power-policy port-index-priority disable command. Only the S5720-EI and S5720-HI support this item.