display uni-mng profile as
Function
The display uni-mng profile as command displays the configuration generated after an AS is bound to service profiles.
This command can only be executed on a parent switch.
Parameters
| Parameter | Description | Value |
|---|---|---|
name as-name |
Specifies the name of an AS. |
The value must have an existing AS name. |
interface interface-type interface-number |
Displays the configuration of a specified interface:
If this parameter is not specified, the configurations of all the service interfaces on an AS are displayed. |
- |
Usage Guidelines
You can run the display uni-mng profile as command to check the configuration generated after an AS is bound to service profiles.
If a fabric port is specified, this command displays only the network QoS profile configuration.
Example
# Display the configuration generated on an AS.
<HUAWEI> display uni-mng profile as name as1 Global ------------------------------------------------------------------------------- Centralized forward mode: disable ------------------------------------------------------------------------------- Portal url-encode: enable ------------------------------------------------------------------------------- Igmp-vlan : -- ------------------------------------------------------------------------------- Authorization-vlan : -- ------------------------------------------------------------------------------- AS-group name: xy Username: admin Privilege-level : 3 Service-type : terminal ssh Bpdu-protection : -- Ipv6 : -- Acl number : 3000 3002 3011 3012 3013 3014 3015 3016 3017 3018 Traffic-limit outbound ARP(Kbps) : 512 Traffic-limit outbound DHCP(Kbps) : 128 ------------------------------------------------------------------------------- Interface fabric-port 0 ------------------------------------------------------------------------------- Port-group name: -- Trust Flag : -- Scheduling Profile : -- Scheduling Mode : -- Weight of Queue 0 : -- Weight of Queue 1 : -- Weight of Queue 2 : -- Weight of Queue 3 : -- Weight of Queue 4 : -- Weight of Queue 5 : -- Weight of Queue 6 : -- Weight of Queue 7 : -- ------------------------------------------------------------------------------- Interface GigabitEthernet0/0/1 ------------------------------------------------------------------------------- Port-group name: -- User-vlan : -- Voice-vlan : -- Pass-vlan : -- Priority-trust : disable User-access-port : disable DHCP snooping : disable IP source check : disable ARP anti-attack check : disable Unicast-suppression(pps) : -- Multicast-suppression(pps) : -- Broadcast-suppression(pps) : -- Rate-limit(Kbps) : -- Port-security : disable Mac-address sticky : disable Port-security aging-time : -- Trust Flag : dscp Scheduling Profile : qos Scheduling Mode : wrr Weight of Queue 0 : -- Weight of Queue 1 : 6 Weight of Queue 2 : -- Weight of Queue 3 : -- Weight of Queue 4 : -- Weight of Queue 5 : -- Weight of Queue 6 : -- Weight of Queue 7 : -- Authentication : -- Authentication maximum user-num : -- MAC-limit : -- Traffic-limit inbound ARP(Kbps) : -- Traffic-limit inbound DHCP(Kbps) : -- Traffic policy profile : -- ------------------------------------------------------------------------------- Interface GigabitEthernet0/0/2 ------------------------------------------------------------------------------- Port-group name: -- User-vlan : -- Voice-vlan : -- Pass-vlan : -- Priority-trust : disable User-access-port : disable DHCP snooping : disable IP source check : disable ARP anti-attack check : disable Unicast-suppression(pps) : -- Multicast-suppression(pps) : -- Broadcast-suppression(pps) : -- Rate-limit(Kbps) : -- Port-security : disable Mac-address sticky : disable Port-security aging-time : -- Trust Flag : dscp Scheduling Profile : qos Scheduling Mode : wrr Weight of Queue 0 : -- Weight of Queue 1 : 6 Weight of Queue 2 : -- Weight of Queue 3 : -- Weight of Queue 4 : -- Weight of Queue 5 : -- Weight of Queue 6 : -- Weight of Queue 7 : -- Authentication : -- Authentication maximum user-num : -- MAC-limit : -- Traffic-limit inbound ARP(Kbps) : -- Traffic-limit inbound DHCP(Kbps) : -- Traffic policy profile : -- ------------------------------------------------------------------------------- ......
Item |
Description |
|---|---|
Global |
Global AS configuration. |
Centralized forward mode |
Whether centralized forwarding is enabled:
To configure centralized forwarding, run the forward-mode centralized command. By default, distributed forwarding is used. |
Portal url-encode |
Whether URL encoding is enabled for an AS:
To disable URL encoding for an AS, run the portal url-encode disable command. By default, URL encoding is enabled for an AS. |
Igmp-vlan |
VLAN in which IGMP Snooping is enabled. If no VLAN is configured, this field displays --. To configure the VLAN, run the as service-vlan igmp-snooping command. |
Authorization-vlan |
Service VLAN created on an AS. If no VLAN is configured, this field displays --. To configure the service VLAN, run the as service-vlan authorization command. |
AS-group name |
Name of the AS group to which an AS belongs. |
Username |
AS administrator user name. If no AS administrator user name is configured, this field displays --. AS administrator user name configured in the AS administrator profile bound to an AS group. To configure an AS administrator user name, run the user password command. |
Privilege-level |
User level. The value is 3 and cannot be changed. |
Service-type |
User access type. The value is terminal ssh and cannot be changed. |
Bpdu-protection |
BPDU protection status of an AS. If BPDU protection is not configured, this field displays --. |
Ipv6 |
Whether IPv6 is enabled on an AS. |
Acl number |
ACL number created on an AS. |
Traffic-limit outbound ARP(Kbps) |
Outbound ARP packet rate limit of the uplink fabric port of an AS, in kbit/s. To set the outbound ARP packet rate limit, run the traffic-limit outbound command. |
Traffic-limit outbound DHCP(Kbps) |
Outbound DHCP packet rate limit of the uplink fabric port of an AS, in kbit/s. To set the outbound ARP packet rate limit, run the traffic-limit outbound command. |
Interface GigabitEthernet0/0/1 Interface GigabitEthernet0/0/2 Interface fabric-port 0 |
Interface name. |
Port-group name |
Name of the port group to which an interface belongs. If an interface is not added to any port group, this field displays -- or disable. |
User-vlan |
Default VLAN. To configure a default VLAN, run the user-vlan command. |
Voice-vlan |
Voice VLAN. To configure a voice VLAN, run the voice-vlan command. |
Pass-vlan |
Allowed VLAN. To configure an allowed VLAN, run the pass-vlan command. |
Priority-trust |
Whether the priority trust function is enabled:
|
User-access-port |
Whether the edge port function is enabled:
To enable the edge port function, run the user-access-port enable command. |
DHCP snooping |
Whether DHCP snooping is enabled:
To enable DHCP snooping, run the dhcp snooping enable command. |
IP source check |
Whether the IP packet check function is enabled:
To enable IP packet check, run the ip source check user-bind enable command. |
ARP anti-attack check |
Whether the dynamic ARP inspection function is enabled:
To enable the dynamic ARP inspection function, run the arp anti-attack check user-bind enable command. |
Unicast-suppression(pps) |
Rate limit for unknown unicast traffic, in pps. To set the rate limit for unknown unicast traffic, run the unicast-suppression command. |
Multicast-suppression(pps) |
Rate limit for multicast traffic, in pps. To set the rate limit for multicast traffic, run the multicast-suppression command. |
Broadcast-suppression(pps) |
Rate limit for broadcast traffic, in pps. To set the rate limit for broadcast traffic, run the broadcast-suppression command. |
Rate-limit(Kbps) |
Traffic rate limit, in kbit/s. To set the traffic rate limit, run the rate-limit command. |
Port-security |
Whether port security is enabled. To enable the port security function, run the port-security enable command. |
Mac-address sticky |
Whether the sticky MAC function is enabled on an interface. To enable the sticky MAC function on an interface, run the port-security mac-address sticky command. |
Port-security aging-time |
Aging time of secure dynamic MAC addresses on an interface. To set this parameter, run the port-security aging-time command. |
Trust Flag |
Packet priority mapping flag. To configure priority mapping, run the trust dscp command. |
Scheduling Profile |
Name of a network QoS profile. |
Scheduling Mode |
Queue scheduling mode. To configure the queue scheduling mode, run the qos { pq | wrr | drr } command. |
Weight of Queue 0 Weight of Queue 1 Weight of Queue 2 Weight of Queue 3 Weight of Queue 4 Weight of Queue 5 Weight of Queue 6 Weight of Queue 7 |
Queue scheduling weight. To configure the queue scheduling weight, run the qos queue command. |
Authentication |
User authentication profile created using the authentication-profile command. |
Authentication maximum user-num |
Maximum number of access users configured in a user access profile. To set this parameter, run the authentication access-user maximum command. |
MAC-limit |
MAC address learning limit. To set the MAC address learning limit, run the mac-limit command. |
Traffic-limit inbound ARP(Kbps) |
Inbound ARP packet rate limit of an AS port, in kbit/s. To set the inbound ARP packet rate limit, run the traffic-limit inbound command. |
Traffic-limit inbound DHCP(Kbps) |
Inbound DHCP packet rate limit of an AS port, in kbit/s. To set the inbound ARP packet rate limit, run the traffic-limit inbound command. |
Traffic policy profile |
Name of the traffic policy profile bound to an AS. |