oam-bind ingress efm interface trigger if-down egress interface

Function

The oam-bind ingress efm interface trigger if-down egress interface command enables EFM to report faults to an interface.

The undo oam-bind ingress efm interface trigger if-down egress interface command cancels the configuration.

By default, unidirectional transmission of information about a fault from EFM OAM to an interface is not configured.

Format

oam-bind ingress efm interface interface-type1 interface-number1 trigger if-down egress interface interface-type2 interface-number2

undo oam-bind ingress efm interface interface-type1 interface-number1 trigger if-down egress interface interface-type2 interface-number2

Parameters

Parameter	Description	Value
interface-type1 interface-number1	Specifies the type and number of the interface enabled with EFM. interface-type1 specifies the interface type. interface-number1 specifies the interface number.	-
interface-type2 interface-number2	Specifies the type and number of the interface bound to an EFM session. interface-type2 specifies the interface type. interface-number2 specifies the interface number.	-

Parameter

Description

Value

interface-type1 interface-number1

Specifies the type and number of the interface enabled with EFM.

interface-type1 specifies the interface type.
interface-number1 specifies the interface number.

interface-type2 interface-number2

Specifies the type and number of the interface bound to an EFM session.

interface-type2 specifies the interface type.
interface-number2 specifies the interface number.

Views

OAM management view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

Association between EFM and an interface in the OAM management view is bidirectional:

After EFM OAM detects a fault, the OAM module notifies the interface associated with EFM OAM of the fault. Then the interface goes Down. After EFM detects that the fault is rectified, the OAM module notifies the interface associated with EFM OAM. Then the interface goes Up.
After the interface goes Down, the OAM module notifies EFM OAM of the interface Down event.
A physical interface associated with EFM cannot be the one that EFM monitors. If EFM is associated with a physical interface that it monitors, the link is locked.

The following commands are used to configure association between EFM and an interface in the OAM management view:

oam-bind efm interface trigger if-down interface
oam-bind interface efm interface trigger if-down
oam-bind ingress efm interface trigger if-down egress interface
oam-bind ingress interface egress efm interface trigger if-down

Table 1 describes the implementation of association between EFM and an interface.

**Table 1** Association between EFM and an EFM-incapable interface
Scenario	Configuration Solution 1	Configuration Solution 2
Bidirectional fault notification between EFM and an interface	Choose either of the following commands (the two commands have the same function): To specify an EFM OAM session first, run the oam-bind efm interface trigger if-down interface command. To specify an interface first, run the oam-bind interface efm interface trigger if-down command. NOTE: After configuring bidirectional fault notification between EFM and an interface, run the display current-configuration command to view the current configuration. The display current-configuration command displays oam-bind ingress interface egress efm interface trigger if-down andoam-bind ingress efm interface trigger if-down egress interface commands, but does not display the oam-bind efm interface trigger if-down interface or oam-bind interface efm interface trigger if-down command. The displayed commands configure reverse transmission directions of fault information.	Run the following commands at a random order: oam-bind ingress efm interface trigger if-down egress interface oam-bind ingress interface egress efm interface trigger if-down
Unidirectional fault notification between EFM and an interface	Choose either of the following commands based on the transmission direction: To configure EFM OAM to report faults to an interface, run the oam-bind ingress efm interface trigger if-down egress interface command. To configure an interface to report faults to EFM OAM, run the oam-bind ingress interface egress efm interface trigger if-down command.	None

Precautions

Before enabling EFM to report faults to an interface, pay attention to the following points:

EFM has been enabled on the interface specified by efm interface interface-type2 interface-number2.
EFM and the interface are associated with each other. After an interface is associated with an EFM session, the interface cannot be associated with other EFM sessions. Similarly, when EFM is bound to an interface, EFM cannot be bound to other interfaces.

Ingress EFM reports faults to the specified interface.

Example

# Configure EFM to report a fault to GigabitEthernet0/0/2.

<HUAWEI> system-view
[HUAWEI] oam-mgr
[HUAWEI-oam-mgr] oam-bind ingress efm interface gigabitethernet 0/0/1 trigger if-down egress interface gigabitethernet 0/0/2