port hybrid untagged vlan

Function

The port hybrid untagged vlan command adds a hybrid interface to the specified VLANs. Frames of the VLANs then pass through the hybrid interface in untagged mode.

The undo port hybrid vlan command removes a hybrid interface from the specified VLANs.

By default, a hybrid interface is added to VLAN 1 in untagged mode.

Format

port hybrid untagged vlan { { vlan-id1 [ to vlan-id2 ] }&<1-10> | all }

undo port hybrid [ untagged ] vlan{ { vlan-id1 [ to vlan-id2 ] }&<1-10> | all }

(Port group view) port hybrid untagged vlan vlan-id3 [ step step-number [ increased | decreased ] ]

(Port group view) undo port hybrid vlan vlan-id3 [ step step-number [ increased | decreased ] ]

Parameters

Parameter	Description	Value
vlan-id1 [ to vlan-id2 ]	Adds a hybrid interface to specified VLANs. vlan-id1 specifies the start VLAN ID. to vlan-id2 specifies the end VLAN ID. The value of vlan-id2 must be greater than or equal to the value of vlan-id1.	The value of vlan-id1 is an integer that ranges from 1 to 4094. The value of vlan-id2 is an integer that ranges from 1 to 4094.
all	Adds a hybrid interface to all VLANs.	-
vlan-id3	Specifies the ID of the start VLAN to be bound to the member port of a port group.	The value is an integer that ranges from 1 to 4094.
step step-number	Specifies the step for the increase or decrease in the value of the VLAN ID. With this parameter specified, the member ports in a port group can be bound to VLANs starting from the one identified by vlan-id3 in an ascending or descending order at a step specified by step-number. This facilitates the subsequent user configuration. For example: A port group has 10 member ports. You can configure increased, and set vlan-id3 to 1 and step-number to 1 in the port hybrid untagged vlan command. After this configuration, member port 1 joins VLAN 1; member port 2 joins VLAN 2... By analogy, member port 10 joins VLAN 10.	The value is an integer that ranges from 1 to 4093.
increased	Specifies an increase in the values of VLAN IDs starting from the one identified by vlan-id3 at a step specified by step-number to bind the VLANs to the member ports of a port group.	By default, Layer 2 ports are bound to the VLANs in an ascending order.
decreased	Specifies a decrease in the values of VLAN IDs starting from the one identified by vlan-id3 at a step specified by step-number to bind the VLANs to the member ports of a port group. When setting decreased, ensure that the value of vlan-id3 is greater than or equal to the number of the member ports of the port group.	-

Views

Ethernet interface view, GE interface view, XGE interface view, 25GE interface view, 40GE interface view, 100GE interface view, MultiGE interface view, VE interface view, Eth-Trunk interface view, port group view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

A hybrid interface can connect to either a user device or a switch. When a hybrid interface is connected to a user device, it must be added to VLANs in untagged mode so that it sends untagged frames.

After a hybrid interface is added to VLANs in untagged mode, the interface removes VLAN tags of frames before sending frames.

Prerequisites

The link type of the interface has been changed to hybrid using the port link-type hybrid command.

Precautions

This command is invalid on a member interface of an Eth-Trunk.
A super VLAN cannot be specified in the command.
If you run the port hybrid untagged vlan command multiple times in the same interface view, the interface is added to all the specified VLANs.

Example

# Add GE0/0/1 to VLAN 3 to VLAN 5 in untagged mode.

<HUAWEI> system-view
[HUAWEI] interface gigabitethernet 0/0/1
[HUAWEI-GigabitEthernet0/0/1] port link-type hybrid
[HUAWEI-GigabitEthernet0/0/1] port hybrid untagged vlan 3 to 5