BRASAAA_1.3.6.1.4.1.2011.5.25.239.4.3 hwDiameterPeerFaultyV6

Trap Buffer Description

The link between pcef and pcrf is abnormal. (DiameterPeerHostName=[hwDiameterPeerHostName],DiameterPeerIP=[hwDiameterPeerIpStr],DiameterPeerPort=[hwDiameterPeerPort],DiameterLocalIf=[hwDiameterLocalIf],DiameterGrpLinkLocalPort=[hwDiameterGrpLinkLocalPort])

The link between a device and a policy server became faulty.

In VS mode, this trap is supported only by the admin VS.

This alarm is supported only on NetEngine 8000 F1A.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Warning
Mnemonic Code	hwDiameterPeerFaultyV6
Trap OID	1.3.6.1.4.1.2011.5.25.239.4.3
MIB	HUAWEI-DIAMETER-MIB
Alarm ID	0x00F1027a
Alarm Name	hwDiameterPeerFaultyV6
Alarm Type	equipmentAlarm
Raise or Clear	Raise
Match trap	BRASAAA_1.3.6.1.4.1.2011.5.25.239.4.4 hwDiameterPeerFaultyResumeV6

Trap Buffer Parameters

Parameter	Description
hwDiameterPeerHostName	Name of the peer device.
hwDiameterPeerIpStr	IPv6 address of the peer device.
hwDiameterPeerPort	Port of the peer device.
hwDiameterLocalIf	Local interface.
hwDiameterGrpLinkLocalPort	Local interface number.

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.239.2.4.1.4	hwDiameterPeerHostName	hwDiameterPeerName
1.3.6.1.4.1.2011.5.25.239.7.1	hwDiameterPeerIpStr	-
1.3.6.1.4.1.2011.5.25.239.2.4.1.3	hwDiameterPeerPort	hwDiameterPeerName
1.3.6.1.4.1.2011.5.25.239.2.3.1.2	hwDiameterLocalIf	hwDiameterLocalName
1.3.6.1.4.1.2011.5.25.239.2.5.1.4	hwDiameterGrpLinkLocalPort	hwDiameterGrpLinkGroupName hwDiameterGrpLinkLocalName hwDiameterGrpLinkPeerName hwDiameterGrpLinkLocalPort

Impact on the System

When the link between a device and a policy server becomes faulty, users that get online through this link are switched to another Up link. If there is no Up link, the users cannot deliver and process services using the policy server.

Possible Causes

Cause 1: A policy server became faulty.

Cause 2: The local IP address or port of the link was changed.

Cause 3: The peer IP address or port of the link was changed.

Procedure

1. Run the display diameter configuration command to check the link status of the Diameter.

If the link is in the Up state, please go to Step 4.
If the link is in the Down state, please go to Step 2.
If the link is in the Error state, please go to Step 4.

2. Run the display diameter configuration command to view configurations of the local and peer devices at two ends of a specified link, including the local interface IP, client port,and peer port. Then, log in to the policy server to check whether configurations of the local and peer devices at two ends of a specified link that are displayed on the portal page are identical with that in the display diameter configuration command output.

If identical, please go to Step 4.
If different, please go to Step 3.

3. Run the diameter-local and diameter-peer commands in the system view to make configurations of the local and peer devices at two ends of a specified link identical with that displayed on the portal page. Run the display diameter configuration command to check the link status.

If the link is in the Up state, please go to Step 5.
If the link is in the Error state, please go to Step 4.

4. Collect alarm information, log information and configuration information, and then contact technical support personnel.

5. End.