DEVM_1.3.6.1.4.1.2011.5.25.129.2.1.9 hwEntityInvalid-67603

Trap Buffer Description

Physical entity failed. (BaseTrapSeverity=[BaseTrapSeverity], BaseTrapProbableCause=[67603], BaseTrapEventType=[BaseTrapEventType], EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalContainedIn=[EntContainedIn], EntPhysicalName=[EntPhysicalName], RelativeResource=[RelativeResource], ReasonDescription=The Monitor bus was faulty.)

Physical entity failed.

In VS mode, this trap is supported only by the admin VS.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Alert
Mnemonic Code	hwEntityInvalid
Trap OID	1.3.6.1.4.1.2011.5.25.129.2.1.9
MIB	HUAWEI-BASE-TRAP-MIB
Alarm ID	0x08130055
Alarm Name	hwEntityInvalid
Alarm Type	equipmentAlarm
Raise or Clear	Raise
Match trap	DEVM_1.3.6.1.4.1.2011.5.25.129.2.1.10 hwEntityResume-67603

Trap Buffer Parameters

Parameter	Description
BaseTrapSeverity	To describe the level of trap.
ProbableCause	To describe the probable cause of trap.
BaseTrapEventType	To describe the type of trap.
EntityPhysicalIndex	The index of the physical entity.
EntContainedIn	The value of entPhysicalIndex for the physical entity.
EntPhysicalName	The textual name of the physical entity.
RelativeResource	This object may contain a key word to indicate the relative resource of an entity.
ReasonDescription	To describe the reason of trap in DisplayString style.

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.129.1.1	hwBaseTrapSeverity	-
1.3.6.1.4.1.2011.5.25.129.1.2	hwBaseTrapProbableCause	-
1.3.6.1.4.1.2011.5.25.129.1.3	hwBaseTrapEventType	-
1.3.6.1.2.1.47.1.1.1.1.4	entPhysicalContainedIn	entPhysicalIndex
1.3.6.1.2.1.47.1.1.1.1.7	entPhysicalName	entPhysicalIndex
1.3.6.1.4.1.2011.5.25.129.1.4	hwBaseTrapRelativeResource	-
1.3.6.1.4.1.2011.5.25.129.1.5	hwBaseTrapReasonDescr	-

Impact on the System

The main control board fails to propperly monitor information about the board in the corresponding slot.

Possible Causes

The Monitor bus was faulty.

Procedure

1. Run the power off and power on commands on the faulty board. After the board is registered, check whether the alarm is cleared.

If so, go to Step 7.
If not, go to Step 2.

2. Remove the board and check whether the pinch board of the Monitor bus is installed well. Reinsert the board. Then, check whether the alarm is cleared.

If so, go to Step 7.
If not, go to Step 3.

3. Replace the board and check whether the alarm is cleared.

If so, go to Step 7.
If not, go to Step 4.

4. Check whether multiple boards report the alarm.

If so, go to Step 5.
If not, go to Step 6.

5. Remove the main control board and check whether the pinch board of the Monitor bus is installed well. Reinsert the main control board. Then, check whether the alarm is cleared.

If so, go to Step 7.
If not, go to Step 6.

6. Collect trap, log, and configuration information, and contact technical support.

7. End.