DEVM_1.3.6.1.4.1.2011.5.25.129.2.1.9 hwEntityInvalid-67629

Trap Buffer Description

Physical entity failed. (BaseTrapSeverity=[BaseTrapSeverity], BaseTrapProbableCause=[67629], BaseTrapEventType=[BaseTrapEventType], EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalContainedIn=[EntContainedIn], EntPhysicalName=[EntPhysicalName], RelativeResource=[RelativeResource], ReasonDescription=One of the internal switches on a power module was not closed.)

Physical entity failed.

In VS mode, this trap is supported only by the admin VS.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Alert
Mnemonic Code	hwEntityInvalid
Trap OID	1.3.6.1.4.1.2011.5.25.129.2.1.9
MIB	HUAWEI-BASE-TRAP-MIB
Alarm ID	0x08130055
Alarm Name	hwEntityInvalid
Alarm Type	equipmentAlarm
Raise or Clear	Raise
Match trap	DEVM_1.3.6.1.4.1.2011.5.25.129.2.1.10 hwEntityResume-67629

Trap Buffer Parameters

Parameter	Description
BaseTrapSeverity	To describe the level of trap.
ProbableCause	To describe the probable cause of trap.
BaseTrapEventType	To describe the type of trap.
EntityPhysicalIndex	The index of the physical entity.
EntContainedIn	The value of entPhysicalIndex for the physical entity.
EntPhysicalName	The textual name of the physical entity.
RelativeResource	This object may contain a key word to indicate the relative resource of an entity.
ReasonDescription	To describe the reason of trap in DisplayString style.

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.129.1.1	hwBaseTrapSeverity	-
1.3.6.1.4.1.2011.5.25.129.1.2	hwBaseTrapProbableCause	-
1.3.6.1.4.1.2011.5.25.129.1.3	hwBaseTrapEventType	-
1.3.6.1.2.1.47.1.1.1.1.4	entPhysicalContainedIn	entPhysicalIndex
1.3.6.1.2.1.47.1.1.1.1.7	entPhysicalName	entPhysicalIndex
1.3.6.1.4.1.2011.5.25.129.1.4	hwBaseTrapRelativeResource	-
1.3.6.1.4.1.2011.5.25.129.1.5	hwBaseTrapReasonDescr	-

Impact on the System

A power failure may lead to power supply insufficiency, causing the board to reset. This indirectly affects services, and therefore this problem needs to be solved.

Possible Causes

One of the internal switches on a power module was not closed.

Procedure

1. Check whether the switches on the power panel are off.

If one or more switches are not off, go to Step 2.
If all switches are off, go to Step 3.

2. Turn off the switches and check whether the alarm is cleared.

If so, go to Step 6.
If not, go to Step 3.

3. Run the slave switchover command to perform an active/standby switchover.

Check whether the alarm is cleared.

If so, go to Step 6.
If not, go to Step 4.

4. Replace the power module. Power off the faulty power module before replacing it.

Then, check whether the alarm is cleared.

If so, go to Step 6.
If not, go to Step 5.

5. Collect trap, log, and configuration information, and contact technical support.

6. End.