The low-speed interface parameter settings reported by the remoter AP mismatch those of the PW.(VcId =[VcId], VcType=[VcType], PeerAddress=[PeerAddress], EncapNum=[EncapNum], JitterBuffer=[JitterBuffer], RtpHeader=[RtpHeader], IdleCode=[IdleCode], InterfaceIndex=[RemoteIfIndex], InterfaceName=[RemoteIfName], RemotePhyType=[RemotePhyType], RemoteLinkType=[RemoteLinkType], RemoteEncap=[RemoteEncap], RemoteMinEncapNum=[RemoteMinEncapNum], RemoteMaxEncapNum=[RemoteMaxEncapNum], RemoteEncapStep=[RemoteEncapStep], RemoteMinJitterBuffer=[RemoteMinJitterBuffer], RemoteMaxJitterBuffer=[RemoteMaxJitterBuffer], RemoteJitterBufferStep=[RemoteJitterBufferStep], RemoteTtpHeader=[RemoteTtpHeader], RemoteMinIdleCode=[RemoteMinIdleCode], RemoteMaxIdleCode=[RemoteMaxIdleCode])
An alarm was generated because the PW parameter settings on the remote AP mismatched those on the aggregation side.
| Trap Attribute | Description |
|---|---|
Alarm or Event |
Alarm |
Trap Severity |
Critical |
Mnemonic Code |
hwRemoteApPwParaMisMatch |
Trap OID |
1.3.6.1.4.1.2011.5.25.119.4.1.2.12 |
MIB |
HUAWEI-PWE3-MIB |
Alarm ID |
0x00F10067 |
Alarm Name |
hwRemoteApPwParaMisMatch |
Alarm Type |
communicationsAlarm |
Raise or Clear |
Raise |
Match trap |
L2VPN_1.3.6.1.4.1.2011.5.25.119.4.1.2.13 hwRemoteApPwParaMisMatchResume |
| Parameter | Description |
|---|---|
VcId |
VC ID of the PW |
VcType |
Encapsulation type supported by the Remote-AP interface |
PeerAddress |
PW peer address |
EncapNum |
TDM frame encapsulation number allowed by the Remote-AP interface |
JitterBuffer |
Jitter buffer depth for TDM frames transmitted by the Remote-AP interface |
RtpHeader |
RTP header carried in a TDM packet transmitted by the Remote-AP interface |
IdleCode |
Idle code filled when jitter buffer underflows during the transmission of TDM frames by the Remote-AP interface |
RemoteIfIndex |
Index of the Remote-AP interface |
RemoteIfName |
Name of the Remote-AP interface |
RemotePhyType |
Physical type of the Remote-AP interface |
RemoteLinkType |
Link type of the Remote-AP interface |
RemoteEncap |
Encapsulation type supported by the remote AC interface |
RemoteMinEncapNum |
Minimum TDM frame encapsulation number allowed by the remote AC interface |
RemoteMaxEncapNum |
Maximum TDM frame encapsulation number allowed by the remote AC interface |
RemoteEncapStep |
TDM frame encapsulation step length allowed by the remote AC interface |
RemoteMinJitterBuffer |
Minimum jitter buffer depth for TDM frames transmitted by the remote AC interface |
RemoteMaxJitterBuffer |
Maximum jitter buffer depth for TDM frames transmitted by the remote AC interface |
RemoteJitterBufferStep |
Step length for the jitter buffer depth of TDM frames transmitted by the remote AC interface |
RemoteTtpHeader |
RTP header carried in a TDM packet transmitted by the remote AC interface |
RemoteMinIdleCode |
Minimum idle code filled when jitter buffer underflows during the transmission of TDM frames by the remote AC interface |
RemoteMaxIdleCode |
Maximum idle code filled when jitter buffer underflows during the transmission of TDM frames by the remote AC interface |
| VB OID | VB Name | VB Index |
|---|---|---|
1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.4 |
hwPWVcPeerAddr |
hwPWVcID hwPWVcType |
1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.54 |
hwPWVcPwTdmEncapsulationNum |
hwPWVcID hwPWVcType |
1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.53 |
hwPWVcPwJitterBufferDepth |
hwPWVcID hwPWVcType |
1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.56 |
hwPWVcPwRtpHeader |
hwPWVcID hwPWVcType |
1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.55 |
hwPWVcPwIdleCode |
hwPWVcID hwPWVcType |
1.3.6.1.4.1.2011.5.25.119.4.1.1.1.1.49 |
hwPWVcIfName |
hwPWVcID hwPWVcType |
1.3.6.1.4.1.2011.5.25.119.8.16.1.2 |
hwL2vpnAcIfPhyType |
hwL2vpnAcIfIndex |
1.3.6.1.4.1.2011.5.25.119.8.16.1.3 |
hwL2vpnAcIfLinkType |
hwL2vpnAcIfIndex |
1.3.6.1.4.1.2011.5.25.119.8.16.1.4 |
hwL2vpnAcIfEncap |
hwL2vpnAcIfIndex |
1.3.6.1.4.1.2011.5.25.119.8.16.1.5 |
hwL2vpnAcIfMinEncapNum |
hwL2vpnAcIfIndex |
1.3.6.1.4.1.2011.5.25.119.8.16.1.6 |
hwL2vpnAcIfMaxEncapNum |
hwL2vpnAcIfIndex |
1.3.6.1.4.1.2011.5.25.119.8.16.1.7 |
hwL2vpnAcIfEncapStep |
hwL2vpnAcIfIndex |
1.3.6.1.4.1.2011.5.25.119.8.16.1.8 |
hwL2vpnAcIfMinJitterBuffer |
hwL2vpnAcIfIndex |
1.3.6.1.4.1.2011.5.25.119.8.16.1.9 |
hwL2vpnAcIfMaxJitterBuffer |
hwL2vpnAcIfIndex |
1.3.6.1.4.1.2011.5.25.119.8.16.1.10 |
hwL2vpnAcIfJitterBufferStep |
hwL2vpnAcIfIndex |
1.3.6.1.4.1.2011.5.25.119.8.16.1.11 |
hwL2vpnAcIfCfgTtpHeader |
hwL2vpnAcIfIndex |
1.3.6.1.4.1.2011.5.25.119.8.16.1.12 |
hwL2vpnAcIfMinIdleCode |
hwL2vpnAcIfIndex |
1.3.6.1.4.1.2011.5.25.119.8.16.1.13 |
hwL2vpnAcIfMaxIdleCode |
hwL2vpnAcIfIndex |
1. Check whether the TDM frame encapsulation number configured on the aggregation side is within the range reported by the remote AP and meets the specified step length requirement. Normally, the TDM frame encapsulation number is 8, 16, 32, or 40.
2. Check whether the maximum jitter buffer depth configured on the aggregation side is within the range reported by the remote AP and meets the specified step length requirement. Normally, the maximum jitter buffer depth is 8, 16, 32, or 64.
3. Check whether the idle code configured on the aggregation side is the same as that reported by the AP.
4. Run the mpls l2vc [ instance-name instance-name ] encapsulation encapsulation-type ip-address vc-id [ [ control-word | no-control-word ] | tunnel-policy tunnel-policy-name | tdm-encapsulation-number tdm-encapsulation-number | tdm-sequence-number | jitter-buffer jitter-buffer | rtp-header | idle-code idle-code ] *command to reconfigure the TDM frame encapsulation number, maximum jitter buffer depth, or idle code on the aggregation side. Then, check whether the alarm is cleared.
5. Collect alarm information and configuration information, and then contact technical support personnel.
6. End.