L2VPN_1.3.6.1.4.1.2011.5.25.119.9.2.15 hwL2vpnOamSd2Near

Trap Buffer Description

The OAM module reported an alarm, indicating that the near-end packet loss ratio exceeded the sd2 threshold. (ServiceType=[ServiceType], ProtocolType=[ProtocolType], VcID=[VcID], VcType=[VcType], PeerAddr=[PeerAddr], IfIndex=[IfIndex], PwMaster=[PwMaster], RmtSiteID=[RmtSiteID], InLabel=[InLabel], OutLabel=[OutLabel], IfName=[IfName], VsiName=[VsiName])

The near-end packet loss ratio exceeded the SD2 threshold.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Error
Mnemonic Code	hwL2vpnOamSd2Near
Trap OID	1.3.6.1.4.1.2011.5.25.119.9.2.15
MIB	HUAWEI-L2VPN-OAM-MIB
Alarm ID	0x0001008e
Alarm Name	hwL2vpnOamSd2Near
Alarm Type	communicationsAlarm
Raise or Clear	Raise
Match trap	L2VPN_1.3.6.1.4.1.2011.5.25.119.9.2.16 hwL2vpnOamSd2NearClear

Trap Buffer Parameters

Parameter	Description
ServiceType	Type of the service: - 0: VLL - 1: VPLS
ProtocolType	Type of the protocol: - 0: SVC - 1: LDP - 2: BGP (not supported for the time being)
VcID	VC ID
VcType	VC type
PeerAddr	IP address of the peer
IfIndex	Interface index
PwMaster	PW identifier: - 1: primary PW - 2: secondary PW
RmtSiteID	Remote site ID
InLabel	VC in-label
OutLabel	VC out-label
IfName	Interface name
VsiName	VSI name

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.119.9.1.1	hwL2vpnServiceType	-
1.3.6.1.4.1.2011.5.25.119.9.1.2	hwL2vpnProtocolType	-
1.3.6.1.4.1.2011.5.25.119.9.1.3	hwL2vpnVcID	-
1.3.6.1.4.1.2011.5.25.119.9.1.4	hwL2vpnVcType	-
1.3.6.1.4.1.2011.5.25.119.9.1.5	hwL2vpnPeerAddr	-
1.3.6.1.4.1.2011.5.25.119.9.1.6	hwL2vpnIfIndex	-
1.3.6.1.4.1.2011.5.25.119.9.1.7	hwL2vpnPwMaster	-
1.3.6.1.4.1.2011.5.25.119.9.1.8	hwL2vpnRmtSiteID	-
1.3.6.1.4.1.2011.5.25.119.9.1.9	hwL2vpnInLabel	-
1.3.6.1.4.1.2011.5.25.119.9.1.10	hwL2vpnOutLabel	-
1.3.6.1.4.1.2011.5.25.119.9.1.11	hwL2vpnIfName	-
1.3.6.1.4.1.2011.5.25.119.9.1.12	hwL2vpnVsiName	-

Impact on the System

Services will not be affected so long as the alarm reported by OAM indicates that there is no fault on the PW.

Possible Causes

The near-end packet loss ratio exceeded the SD2 threshold.

Procedure

1. Perform the troubleshooting operations described in hwMplsTpOamNearDualLossSD2 to rectify the fault. Then, check whether the alarm is cleared.

If the alarm is cleared, go to Step 3.
If alarm persists, go to Step 2.

2. Collect alarm information and configuration information, and then contact technical support personnel.

3. End.