L2VPN_1.3.6.1.4.1.2011.5.25.119.9.2.19 hwL2vpnOamCsf

Trap Buffer Description

OAM reported an alarm about a client signal failure. (ServiceType=[ServiceType], ProtocolType=[ProtocolType], VcID=[VcID], VcType=[VcType], PeerAddr=[PeerAddr], IfIndex=[IfIndex], PwMaster=[PwMaster], RmtSiteID=[RmtSiteID], InLabel=[InLabel], OutLabel=[OutLabel], IfName=[IfName], VsiName=[VsiName])

OAM detected a client signal failure.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Critical
Mnemonic Code	hwL2vpnOamCsf
Trap OID	1.3.6.1.4.1.2011.5.25.119.9.2.19
MIB	HUAWEI-L2VPN-OAM-MIB
Alarm ID	0x0000345A
Alarm Name	hwL2vpnOamCsf
Alarm Type	communicationsAlarm
Raise or Clear	Raise
Match trap	L2VPN_1.3.6.1.4.1.2011.5.25.119.9.2.20 hwL2vpnOamCsfClear

Trap Buffer Parameters

Parameter	Description
ServiceType	Type of the service: 0: VPWS. 1: VPLS.
ProtocolType	Type of the protocol: 0: SVC. 1: LDP. 2: BGP (not supported for the time being).
VcID	VC ID.
VcType	VC type.
PeerAddr	IP address of the peer.
IfIndex	Interface index.
PwMaster	PW identifier: 1: primary PW. 2: secondary PW.
RmtSiteID	Remote site ID.
InLabel	VC in-label.
OutLabel	VC out-label.
IfName	Interface name.
VsiName	VSI name.

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.119.9.1.1	hwL2vpnServiceType	-
1.3.6.1.4.1.2011.5.25.119.9.1.2	hwL2vpnProtocolType	-
1.3.6.1.4.1.2011.5.25.119.9.1.3	hwL2vpnVcID	-
1.3.6.1.4.1.2011.5.25.119.9.1.4	hwL2vpnVcType	-
1.3.6.1.4.1.2011.5.25.119.9.1.5	hwL2vpnPeerAddr	-
1.3.6.1.4.1.2011.5.25.119.9.1.6	hwL2vpnIfIndex	-
1.3.6.1.4.1.2011.5.25.119.9.1.7	hwL2vpnPwMaster	-
1.3.6.1.4.1.2011.5.25.119.9.1.8	hwL2vpnRmtSiteID	-
1.3.6.1.4.1.2011.5.25.119.9.1.9	hwL2vpnInLabel	-
1.3.6.1.4.1.2011.5.25.119.9.1.10	hwL2vpnOutLabel	-
1.3.6.1.4.1.2011.5.25.119.9.1.11	hwL2vpnIfName	-
1.3.6.1.4.1.2011.5.25.119.9.1.12	hwL2vpnVsiName	-

Impact on the System

The availability of the protection group will be affected after a PW in the protection group becomes faulty.

Possible Causes

The local end detected a client signal failure and sent a CSF OAM packet to notify the remote end of the failure.

Procedure

1. Run the display current-configuration command to check whether the AC link is shut down.

If the link is shut down, go to Step 2.
If the link is not shut down, go to Step 3.

2. Run the undo shutdown command and check whether the AC link goes Up.

If the link goes Up, go to Step 4.
If the link is still Down, go to Step 3.

3. Collect alarm information and configuration information, and then contact technical support personnel.

4. End.