L2VPN_1.3.6.1.4.1.2011.5.25.119.9.2.1 hwL2vpnOamDloc

Trap Buffer Description

OAM reported an alarm about PW disconnection. (ServiceType=[ServiceType], ProtocolType=[ProtocolType], VcID=[VcID], VcType=[VcType], PeerAddr=[PeerAddr], IfIndex=[IfIndex], PwMaster=[PwMaster], RmtSiteID=[RmtSiteID], InLabel=[InLabel], OutLabel=[OutLabel], IfName=[IfName], VsiName=[VsiName])

The PW connectivity status detected by OAM changed from Up to Down.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Error
Mnemonic Code	hwL2vpnOamDloc
Trap OID	1.3.6.1.4.1.2011.5.25.119.9.2.1
MIB	HUAWEI-L2VPN-OAM-MIB
Alarm ID	0x0d4e0000
Alarm Name	hwL2vpnOamDloc
Alarm Type	communicationsAlarm
Raise or Clear	Raise
Match trap	L2VPN_1.3.6.1.4.1.2011.5.25.119.9.2.2 hwL2vpnOamDlocClear

Trap Buffer Parameters

Parameter	Description
ServiceType	Type of the service: 0: VPWS. 1: VPLS.
ProtocolType	Type of the protocol: 0: SVC. 1: LDP. 2: BGP (not supported for the time being).
VcID	VC ID.
VcType	VC type.
PeerAddr	IP address of the peer.
IfIndex	Interface index.
PwMaster	PW identifier: 1: primary PW. 2: secondary PW.
RmtSiteID	Remote site ID.
InLabel	VC in-label.
OutLabel	VC out-label.
IfName	Interface name.
VsiName	VSI name.

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.119.9.1.1	hwL2vpnServiceType	-
1.3.6.1.4.1.2011.5.25.119.9.1.2	hwL2vpnProtocolType	-
1.3.6.1.4.1.2011.5.25.119.9.1.3	hwL2vpnVcID	-
1.3.6.1.4.1.2011.5.25.119.9.1.4	hwL2vpnVcType	-
1.3.6.1.4.1.2011.5.25.119.9.1.5	hwL2vpnPeerAddr	-
1.3.6.1.4.1.2011.5.25.119.9.1.6	hwL2vpnIfIndex	-
1.3.6.1.4.1.2011.5.25.119.9.1.7	hwL2vpnPwMaster	-
1.3.6.1.4.1.2011.5.25.119.9.1.8	hwL2vpnRmtSiteID	-
1.3.6.1.4.1.2011.5.25.119.9.1.9	hwL2vpnInLabel	-
1.3.6.1.4.1.2011.5.25.119.9.1.10	hwL2vpnOutLabel	-
1.3.6.1.4.1.2011.5.25.119.9.1.11	hwL2vpnIfName	-
1.3.6.1.4.1.2011.5.25.119.9.1.12	hwL2vpnVsiName	-

Impact on the System

After OAM is deployed and an APS instance is bound to the PW protection group:

The service traffic will be switched from the primary PW to the secondary PW if OAM reports an alarm about the primary PW.
The service traffic will not be switched or affected if OAM reports an alarm about the secondary PW.

Possible Causes

Cause 1: MPLS OAM or MPLS-TP OAM configurations were incorrect.
Cause 2: The PW detected by OAM became faulty.

Procedure

1. If MPLS OAM is configured, run the display this command in the MPLS-OAM view to check MPLS OAM configurations.

If the configurations are correct, go to Step 2.
If the configurations are incorrect, go to Step 4.

2. If MPLS-TP OAM is configured, perform the troubleshooting operations described in hwMplsTpOamLossOfConnection to rectify the fault.

If the fault is rectified, go to Step 5.
If the fault persists, go to Step 3.

3. Perform the troubleshooting operations described in hwPWVcDown and hwSvcDown to rectify the fault.

If the fault is rectified, go to Step 5.
If the fault persists, go to Step 4.

4. Collect alarm information and configuration information, and then contact technical support personnel.

5. End.