MPLS_LSPM_1.3.6.1.4.1.2011.5.25.121.2.1.7 hwMplsTeFrrSwitch

Trap Buffer Description

Tunnel frr switches. (TunnelId=[TunnelId], LocalLspId=[LocalLspId], IngressLsrId=[IngressLsrId], EgressLsrId=[EgressLsrId], TunnelAdminStatus=[TunnelAdminStatus], TunnelOperStatus=[TunnelOperStatus], BypassSessionTunnelId=[BypassTunnelId], BypassLocalLspId=[BypassLocalLspId], BypassIngressLsrId=[BypassIngressLsrId], BypassEgressLsrId=[BypassEgressLsrId], TunnelType=[TunnelType], ProtectedIfName=[ProtectedIfName], BypassTunnelPath=[BypassTunnelPath], SubGroupId=[SubGroupId], SubGroupOrignatorId=[SubGroupOrignatorId], FrrMethod=[FrrMethod])

Traffic switched to the bypass tunnel after the primary tunnel failed.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Event
Trap Severity	Warning
Mnemonic Code	FRRSWITCH
Trap OID	1.3.6.1.4.1.2011.5.25.121.2.1.7
MIB	HUAWEI-MPLS-EXTEND-MIB
Alarm ID	This is an event trap and does not involve alarm ID.
Alarm Name	This is an event trap and does not involve alarm name.
Alarm Type	This is an event trap and does not involve alarm type.
Raise or Clear	This is an event trap and does not involve alarm generation or clearance.
Match trap	-

Trap Buffer Parameters

Parameter	Description
TunnelId	Primary tunnel ID.
LocalLspId	LSP ID of the primary tunnel.
IngressLsrId	Ingress LSR ID of the primary tunnel.
EgressLsrId	Egress LSR ID of the primary tunnel.
TunnelAdminStatus	Administrative status of the primary tunnel.
TunnelOperStatus	Operational status of the primary tunnel.
BypassTunnelId	Bypass Tunnel Id.
BypassLocalLspId	Bypass Local Lsp Id.
BypassIngressLsrId	Bypass Ingress Lsr Id.
BypassEgressLsrId	Bypass Egress Lsr Id.
TunnelType	Primary tunnel type.
ProtectedIfName	Protected Interface Name.
BypassTunnelPath	Bypass Tunnel Path.
SubGroupId	Sub-Group ID.
SubGroupOrignatorId	Sub-Group Originator ID.
FrrMethod	FRR mode (facility,one-to-one).

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.121.1.1.1.7	hwMplsTunnelAdminStatus	hwMplsTunnelIndex hwMplsTunnelInstance hwMplsTunnelIngressLSRId hwMplsTunnelEgressLSRId
1.3.6.1.4.1.2011.5.25.121.1.1.1.8	hwMplsTunnelOperStatus	hwMplsTunnelIndex hwMplsTunnelInstance hwMplsTunnelIngressLSRId hwMplsTunnelEgressLSRId
1.3.6.1.4.1.2011.5.25.121.2.2.15	hwMplsSessionTunnelId	-
1.3.6.1.4.1.2011.5.25.121.2.2.16	hwMplsLocalLspId	-
1.3.6.1.4.1.2011.5.25.121.2.2.17	hwMplsIngressLsrId	-
1.3.6.1.4.1.2011.5.25.121.2.2.18	hwMplsEgressLsrId	-

Procedure

1. Check whether the configurations for the current tunnel interface, RSVP, an IGP, link connectivity, and bandwidth for links along the tunnel are correct.

If an explicit path is configured, check whether the interfaces along the explicit path are faulty.
If an interface fails, go to Step 2.
If all interfaces work properly, go to Step 3.
If no explicit path is configured, check whether the path that satisfies the configuration condition exists. If the path exists, go to Step 3.

2. Rectify the link fault and check whether the log is displayed:

If the log is no longer displayed, go to Step 5.
If the log persists, go to Step 3.

3. Run the display mpls te tunnel-interface last-error command to check error information.

Check possible causes for error information before proceeding to the next step:
"Cspf failed to calculate a path for Tunnel": CSPF is enabled on the ingress but CSPF fails to calculate a path for the tunnel. Check whether configurations for explicit paths are correct, whether IS-IS TE or OSPF TE has been enabled, and whether routing configurations are correct. After correcting the configuration, check whether the log is displayed:
If the log is no longer displayed, go to Step 5.
If the log persists, go to Step 4.
"Receive Error-Node(192.168.1.2) at ENUM_TEM_LSPFSM_STATE_SETUPING state." or "Routing Problem:Bad initial subobject.": A node (192.168.1.2) on the tunnel is defective. Check that MPLS TE and RSVP-TE configurations are correct on this node. Then check whether the log is displayed.
If the log is no longer displayed, go to Step 5.
If the log persists, go to Step 4.
"Sig. reports connect timeout at ENUM_TEM_LSPFSM_STATE_SETUPING state.": RSVP-TE is not enabled on a downstream node or its inbound interface. Enable RSVP-TE and check whether the log is displayed.
If the log is no longer displayed, go to Step 5.
If the log persists, go to Step 4.
"Crlsp receive Sig. ResvTear at ENUM_TEM_LSPFSM_STATE_SETUPING state.": A link to a downstream node or a downstream node fails. Check and rectify the fault. Check whether the log is displayed.
If the log is no longer displayed, go to Step 5.
If the log persists, go to Step 4.
If other errors occur, go to Step 4.
If no error information is displayed, go to Step 4.

4. Collect the trap information, log information, and configuration of the router, and Collect log information and configuration information, and then contact technical support personnel..

5. End.