PIM_1.3.6.1.4.1.2011.5.25.149.4.0.23 routeExceed

Trap Buffer Description

The number of existed routing entries exceeded the global upper limit. (LimitType=[LimitType], AddressFamily=[AddressFamily], CurrentCount=[CurrentCount], LimitCount=[LimitCount],SrcAddr=[SrcAddr], GrpAddr=[GrpAddr], InstanceName=[InstanceName])

The number of created PIM entries on the device reached the specified limit.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Critical
Mnemonic Code	PIM_ROUTE_EXCEED
Trap OID	1.3.6.1.4.1.2011.5.25.149.4.0.23
MIB	HUAWEI-PIM-STD-MIB
Alarm ID	0x00F100ec
Alarm Name	PIM_ROUTE_EXCEED
Alarm Type	qualityOfServiceAlarm
Raise or Clear	Raise
Match trap	PIM_1.3.6.1.4.1.2011.5.25.149.4.0.24 routeExceedClear

Trap Buffer Parameters

Parameter	Description
LimitType	Type of entry for which an entry number limit takes effect, which is one of the followings: PIM-SM (, G) entry PIM-SM (S, G) entry PIM-DM (, G) entry PIM-DM (S, G) entry
AddressFamily	Address family
CurrentCount	Number of created PIM entries on the device
LimitCount	Limit on the number of PIM entries on the device
SrcAddr	Multicast source address If the set limited value is less than the existed routes number, the values of SrcAddr and GrpAddr are 0.0.0.0.
GrpAddr	Multicast group address If the set limited value is less than the existed routes number, the values of SrcAddr and GrpAddr are 0.0.0.0.
InstanceName	Instance of which the number of created (S, G) entries on the device reaches the specified limit

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.149.4.1.74	hwPimNotificationLimitType	-
1.3.6.1.4.1.2011.5.25.149.4.1.62	hwPimNotificationAddressType	-
1.3.6.1.4.1.2011.5.25.149.4.1.72	hwPimNotificationTypeTotalCount	-
1.3.6.1.4.1.2011.5.25.149.4.1.73	hwPimNotificationTypeLimit	-
1.3.6.1.4.1.2011.5.25.149.4.1.69	hwPimNotificationSrcAddr	-
1.3.6.1.4.1.2011.5.25.149.4.1.70	hwPimNotificationGrpAddr	-
1.3.6.1.4.1.2011.5.25.149.4.1.60	hwPimInstanceName	-

Impact on the System

The number of PIM entries reaches the specified limit.

No new entries can be created.

Possible Causes

Cause 1: Entry create
Cause 2: Configuration change

Procedure

Cause 1: Entry create
1. Run the display multicast global outgoing-interface pim sm statistics command to check whether the number limit is low.
- If the limit is low, go to Step 2.
- If the limit is not low, go to Step 3.
2. Run the multicast global limit command to set a proper limit. Then, check whether the alarm is cleared.
- If the alarm is cleared, go to Step 4.
- If the alarm persists, go to Step 3.
3. Collect alarm information and configuration information, and then contact technical support personnel.

4. End.
Cause 2: Configuration change
The same as Cause 1.