PIM_1.3.6.1.4.1.2011.5.25.149.4.0.30 hwPimVrfTypeSGThresholdExceed

Trap Buffer Description

The number of existed routing entries exceeded the vpn upper threshold. (LimitType=[LimitType], AddressFamily=[AddressFamily], VpnName=[VpnName], CurrentCount=[CurrentCount], LimitCount=[LimitCount], ThresholdCount=[ThresholdCount])

The number of PIM-SM entries in the VPN instance reached or exceeded the configured log trigger threshold.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Warning
Mnemonic Code	PIM_VRF_ROUTE_THRESHOLD
Trap OID	1.3.6.1.4.1.2011.5.25.149.4.0.30
MIB	HUAWEI-PIM-STD-MIB
Alarm ID	0x00F102ba
Alarm Name	PIM_VRF_ROUTE_THRESHOLD
Alarm Type	qualityOfServiceAlarm
Raise or Clear	Raise
Match trap	PIM_1.3.6.1.4.1.2011.5.25.149.4.0.31 hwPimVrfTypeSGThresholdExceedClear

Trap Buffer Parameters

Parameter	Description
LimitType	Type of entry for which an entry number limit takes effect, which is one of the followings: PIM-SM (*, G) entry PIM-SM (S, G) entry
AddressFamily	Address family.
VpnName	Name of a VPN instance.
CurrentCount	Number of PIM-SM entries in the VPN instance.
LimitCount	Limit on the number of PIM-SM entries.
ThresholdCount	Log trigger threshold for the number of PIM-SM entries.

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.149.4.1.74	hwPimNotificationLimitType	-
1.3.6.1.4.1.2011.5.25.149.4.1.62	hwPimNotificationAddressType	-
1.3.6.1.4.1.2011.5.25.149.4.1.60	hwPimInstanceName	-
1.3.6.1.4.1.2011.5.25.149.4.1.72	hwPimNotificationTypeTotalCount	-
1.3.6.1.4.1.2011.5.25.149.4.1.73	hwPimNotificationTypeLimit	-
1.3.6.1.4.1.2011.5.25.149.4.1.75	hwPimNotificationLimitUpperThreshold	-

Procedure

Cause 1: Entry create
1. Check whether AddressFamily is IPv4.If AddressFamily is IPv4, the log is triggered in the IPv4 address family of a VPN instance. Perform the following operations:
- a. Run the display multicast pim sm statistics command to check whether the log trigger threshold or the number limit is low.
- If the log trigger threshold or the number limit is low, go to Step b.
- If the log trigger threshold or the number limit is not low, go to Step c.
- b. Run the multicast limit pim sm command to adjust the log trigger threshold or the number limit. Then check whether the fault is rectified.
- If the fault is rectified, go to Step d.
- If the fault is not rectified, go to Step c.
- c. Collect log information and configuration information, and then contact technical support personnel.
- d. End.
2. Check whether AddressFamily is IPv6. If AddressFamily is IPv6, the log is triggered in the IPv6 address family of a VPN instance. Perform the following operations:
- a. Run the display multicast ipv6 pim sm statistics command to check whether the log trigger threshold or the number limit is low.
- If the log trigger threshold or the number limit is low, go to Step b.
- If the log trigger threshold or the number limit is not low, go to Step c.
- b. Run the multicast ipv6 limit pim sm command to adjust the log trigger threshold or the number limit. Then check whether the fault is rectified.
- If the fault is rectified, go to Step d.
- If the fault is not rectified, go to Step c.
- c. Collect log information and configuration information, and then contact technical support personnel.
- d. End.
Cause 2: Configuration change
The same as Cause 1.