TPOAM_1.3.6.1.4.1.2011.5.25.235.1.5.3 hwMplsTpOamRemoteDefectIndication

Trap Buffer Description

RDI alarm start. (MegId=[MegId], MegId=[Meg_Id], MeIndex=[MeIndex], MeType=[MeType], MeDirection=[MeDirection], IfName=[IfName], PeerIP=[PeerIP], VcId=[VcId], VcType=[VcType], RemoteIp=[RemoteIp], Ttl=[Ttl], MepId=[MepId], RemoteMepId=[RemoteMepId], LspName=[LspName], VsiName=[VsiName])

TP OAM detected a remote fault.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Event
Trap Severity	Warning
Mnemonic Code	hwMplsTpOamRemoteDefectIndication
Trap OID	1.3.6.1.4.1.2011.5.25.235.1.5.3
MIB	HUAWEI-TPOAM-MIB
Alarm ID	This is an event trap and does not involve alarm ID.
Alarm Name	This is an event trap and does not involve alarm name.
Alarm Type	This is an event trap and does not involve alarm type.
Raise or Clear	This is an event trap and does not involve alarm generation or clearance.
Match trap	-

Trap Buffer Parameters

Parameter	Description
MegId	Name of a MEG.
Meg_Id	Name of a MEG.
MeIndex	Index of an ME.
MeType	ME type: 1: PW VLL 2: PW VSI 3: TE -CR LSP 4: Section 5: Associate.
MeDirection	Tunnel type for an ME: ingress egress dual.
IfName	Interface name.
PeerIP	Peer IP address.
VcId	VC ID.
VcType	VC type.
RemoteIp	IP address of an RMEP.
Ttl	TTL value.
MepId	Local ME ID.
RemoteMepId	RMEP ID.
LspName	LSP name.
VsiName	VSI name.

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.235.1.1.1.1.1	hwMplsTpOamMegId	hwMplsTpOamMegId
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.2	hwMplsTpOamMeType	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.3	hwMplsTpOamMeDirection	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.4	hwMplsTpOamMeIfName	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.5	hwMplsTpOamMePeerip	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.6	hwMplsTpOamMeVcId	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.7	hwMplsTpOamMeVcType	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.8	hwMplsTpOamMeVllRemotePeerIp	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.9	hwMplsTpOamMEVllTTL	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.10	hwMplsTpOamMeMepId	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.11	hwMplsTpOamMeRemoteMepId	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.13	hwMplsTpOamMeLspName	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.14	hwMplsTpOamMeVsiName	hwMplsTpOamMegId hwMplsTpOamMeIndex

Procedure

1. Run the display interface command to check whether any physical interface connected to the MPLS TE tunnel is shut down.

If any physical interface connected to the MPLS TE tunnel is shut down, go to Step 2.
If no physical interface connected to the MPLS TE tunnel is shut down, go to Step 3.

2. Run the undo shutdown command to enable the physical interface, and check whether the alarm is cleared.

If the alarm is cleared, go to Step 6.
If the alarm is not cleared, go to Step 3.

3. Run the display mpls-tp oam meg command to check whether the MEP is enabled to receive CCMs and the RMEP is enabled to send CCMs in the MEG.

If the MEP is enabled to receive CCMs and the RMEP is enabled to send CCMs, go to Step 5.
If the MEP is not enabled to receive CCMs and the RMEP is not enabled to send CCMs, go to Step 4.

4. Enable the MEP to receive CCMs, and enable the RMEP to send CCMs. Then check whether the alarm is cleared.

If the alarm is cleared, go to Step 6.
If the alarm is not cleared, go to Step 5.

5. Collect log information and configuration information, and then contact technical support personnel.

6. End.