TUNNEL-TE_1.3.6.1.4.1.2011.5.12.7.1.4.5 hwMplsApsLost

Trap Buffer Description

Tunnel protection group did not receive APS frames from protection tunnel. (IfIndex=[WorkTunnelIfIndex], SessionTunnelId=[SessionTunnelId], LocalLspId=[LocalLspId], IngressLsrId=[IngressLsrId], EgressLsrId=[EgressLsrId], WorkTunnel=[WorkTunnel], SignalingProtocol=[SgnlPrtcl], SignalledTunnelName=[SignalledTunnelName])

No APS frame was transmitted on the protect tunnel in the tunnel protection group.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Warning
Mnemonic Code	hwMplsApsLost
Trap OID	1.3.6.1.4.1.2011.5.12.7.1.4.5
MIB	HUAWEI-MPLSOAM-MIB
Alarm ID	0x0001006a
Alarm Name	hwMplsApsLost
Alarm Type	communicationsAlarm
Raise or Clear	Raise
Match trap	TUNNEL-TE_1.3.6.1.4.1.2011.5.12.7.1.4.6 hwMplsApsLostRecovery

Trap Buffer Parameters

Parameter	Description
SessionTunnelId	Indicates the tunnel ID.
LocalLspId	Indicates the local LSP ID.
IngressLsrId	Indicates the LSR ID of the ingress node.
EgressLsrId	Indicates the LSR ID of the egress node.
WorkTunnel	Indicates the name of the working tunnel in the protection group.
SgnlPrtcl	Indicates the tunnel protocol ID. The options are as follows: 1: RSVP 2: STATIC 3: CRSTATIC
WorkTunnelIfIndex	Index of the tunnel interface
SignalledTunnelName	Tunnel alias.

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.12.7.1.3.1.1.3	hwMplsPsWorkTunnName	hwMplsPsIndex
1.3.6.1.4.1.2011.5.25.121.1.1.1.30	hwMplsTunnelSignalProto	hwMplsTunnelIndex hwMplsTunnelInstance hwMplsTunnelIngressLSRId hwMplsTunnelEgressLSRId
1.3.6.1.4.1.2011.5.25.121.1.1.1.33	hwMplsTunnelSignalledTunnelName	hwMplsTunnelIndex hwMplsTunnelInstance hwMplsTunnelIngressLSRId hwMplsTunnelEgressLSRId

VB OID

VB Name

VB Index

1.3.6.1.4.1.2011.5.12.7.1.3.1.1.3

hwMplsPsWorkTunnName

hwMplsPsIndex

1.3.6.1.4.1.2011.5.25.121.1.1.1.30

hwMplsTunnelSignalProto

hwMplsTunnelIndex

hwMplsTunnelInstance

hwMplsTunnelIngressLSRId

hwMplsTunnelEgressLSRId

1.3.6.1.4.1.2011.5.25.121.1.1.1.33

hwMplsTunnelSignalledTunnelName

hwMplsTunnelIndex

hwMplsTunnelInstance

hwMplsTunnelIngressLSRId

hwMplsTunnelEgressLSRId

Procedure

1. Run the display mpls te tunnel-interface command and check whether the Tunnel State Desc field is displayed as UP.

If so, go to step 2.
If not, see "TE Tunnel Is Down".

2. Run the ping lsp te tunnel interface-number command on the ingress of the protection tunnel to check whether traffic runs properly.

If so, go to step 3.
If not, see "Host Cannot Transmit Packets Along an LSP".

3. Check whether the physical link over which the tunnel is set up is faulty.

If so, repair the physical link.
If not, go to step 4.

4. Collect the alarm, log, and configuration information, and Collect alarm information and configuration information, and then contact technical support personnel..

5. End.