TUNNEL-TE_1.3.6.1.4.1.2011.5.12.7.1.4.9 hwMplsApsDegraded

Trap Buffer Description

Tunnel protection group receives an APS degraded alarm.(IfIndex=[WorkTunnelIfIndex], SessionTunnelId=[SessionTunnelId], LocalLspId=[LocalLspId], IngressLsrId=[IngressLsrId], EgressLsrId=[EgressLsrId],WorkTunnel=[WorkTunnel], SignalingProtocol=[SgnlPrtcl], SignalledTunnelName=[SignalledTunnelName])

A alarm was generated when tunnel protection group receives an APS degraded.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Critical
Mnemonic Code	TUNNEL_APS_DEGRADED
Trap OID	1.3.6.1.4.1.2011.5.12.7.1.4.9
MIB	HUAWEI-MPLSOAM-MIB
Alarm ID	0x00010012
Alarm Name	hwMplsApsDegraded
Alarm Type	qualityOfServiceAlarm
Raise or Clear	Raise
Match trap	TUNNEL-TE_1.3.6.1.4.1.2011.5.12.7.1.4.10 hwMplsApsDegradedRecovery

Trap Buffer Parameters

Parameter	Description
SessionTunnelId	Tunnel ID of a session
LocalLspId	LSP ID of a tunnel session
IngressLsrId	LSR ID of the ingress of a tunnel
EgressLsrId	LSR ID of the egress of a tunnel
WorkTunnel	Name of the working tunnel in a tunnel protection group
SgnlPrtcl	Signaling protocol used by a tunnel session including: 1: RSVP 2: STATIC 3: CRSTATIC
WorkTunnelIfIndex	Work Tunnel Interface Index
SignalledTunnelName	Tunnel alias.

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.12.7.1.3.1.1.3	hwMplsPsWorkTunnName	hwMplsPsIndex
1.3.6.1.4.1.2011.5.25.121.1.1.1.30	hwMplsTunnelSignalProto	hwMplsTunnelIndex hwMplsTunnelInstance hwMplsTunnelIngressLSRId hwMplsTunnelEgressLSRId
1.3.6.1.4.1.2011.5.25.121.1.1.1.33	hwMplsTunnelSignalledTunnelName	hwMplsTunnelIndex hwMplsTunnelInstance hwMplsTunnelIngressLSRId hwMplsTunnelEgressLSRId

VB OID

VB Name

VB Index

1.3.6.1.4.1.2011.5.12.7.1.3.1.1.3

hwMplsPsWorkTunnName

hwMplsPsIndex

1.3.6.1.4.1.2011.5.25.121.1.1.1.30

hwMplsTunnelSignalProto

hwMplsTunnelIndex

hwMplsTunnelInstance

hwMplsTunnelIngressLSRId

hwMplsTunnelEgressLSRId

1.3.6.1.4.1.2011.5.25.121.1.1.1.33

hwMplsTunnelSignalledTunnelName

hwMplsTunnelIndex

hwMplsTunnelInstance

hwMplsTunnelIngressLSRId

hwMplsTunnelEgressLSRId

Impact on the System

When the alarm is reported, one tunnel in the protection group is faulty and this impairs the usability of the protection group, or lock is configured.

Possible Causes

1.One tunnel in the protection group is faulty.

2.Lock is configured for protection group.

Procedure

1.Check the status of protection group, if locked, delete the configuration of lock.

2. Check the status of Tunnel APS protection group and Tunnel status, to determine whether there is a fault Tunnel.

If not, proceed to step 5.
If yes, go to step 3.

3. Check whether the corresponding port of the faulty tunnel is shut down.

If yes, open the closed port.
If no, proceed to Step 4.

4. Check whether the optical fiber of the port corresponding to the faulty tunnel is properly connected.

If yes, go to step 5.
If not, reconnect the fiber.

5. Collect log information and configuration information, and then contact technical support personnel.

6. End.