L2VPN_1.3.6.1.4.1.2011.5.25.119.9.2.5 hwL2vpnOamRdi

Trap Buffer Description

OAM reported an alarm about a remote defect. (ServiceType=[ServiceType], ProtocolType=[ProtocolType], VcID=[VcID], VcType=[VcType], PeerAddr=[PeerAddr], IfIndex=[IfIndex], PwMaster=[PwMaster], RmtSiteID=[RmtSiteID], InLabel=[InLabel], OutLabel=[OutLabel], IfName=[IfName], VsiName=[VsiName])

OAM reported an RDI alarm.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Error
Mnemonic Code	hwL2vpnOamRdi
Trap OID	1.3.6.1.4.1.2011.5.25.119.9.2.5
MIB	HUAWEI-L2VPN-OAM-MIB
Alarm ID	0x00003459
Alarm Name	hwL2vpnOamRdi
Alarm Type	communicationsAlarm
Raise or Clear	Raise
Match trap	L2VPN_1.3.6.1.4.1.2011.5.25.119.9.2.6 hwL2vpnOamRdiClear

Trap Buffer Parameters

Parameter	Description
ServiceType	Type of the service: 0: VLL. 1: VPLS.
ProtocolType	Type of the protocol: 0: SVC. 1: LDP. 2: BGP (not supported for the time being).
VcID	VC ID.
VcType	VC type.
PeerAddr	IP address of the peer.
IfIndex	Interface index.
PwMaster	PW identifier: 1: primary PW. 2: secondary PW.
RmtSiteID	Remote site ID.
InLabel	VC in-label.
OutLabel	VC out-label.
IfName	Interface name.
VsiName	VSI name.

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.119.9.1.1	hwL2vpnServiceType	-
1.3.6.1.4.1.2011.5.25.119.9.1.2	hwL2vpnProtocolType	-
1.3.6.1.4.1.2011.5.25.119.9.1.3	hwL2vpnVcID	-
1.3.6.1.4.1.2011.5.25.119.9.1.4	hwL2vpnVcType	-
1.3.6.1.4.1.2011.5.25.119.9.1.5	hwL2vpnPeerAddr	-
1.3.6.1.4.1.2011.5.25.119.9.1.6	hwL2vpnIfIndex	-
1.3.6.1.4.1.2011.5.25.119.9.1.7	hwL2vpnPwMaster	-
1.3.6.1.4.1.2011.5.25.119.9.1.8	hwL2vpnRmtSiteID	-
1.3.6.1.4.1.2011.5.25.119.9.1.9	hwL2vpnInLabel	-
1.3.6.1.4.1.2011.5.25.119.9.1.10	hwL2vpnOutLabel	-
1.3.6.1.4.1.2011.5.25.119.9.1.11	hwL2vpnIfName	-
1.3.6.1.4.1.2011.5.25.119.9.1.12	hwL2vpnVsiName	-

Impact on the System

After OAM is deployed and an APS instance is bound to the PW protection group:

The service traffic will be switched from the primary PW to the secondary PW if OAM reports an alarm about the primary PW.
The service traffic will not be switched or affected if OAM reports an alarm about the secondary PW.

Possible Causes

The remote end detected a LOC alarm and notified the local end.

Procedure

1. Perform the troubleshooting operations described in hwMplsTpOamRemoteDefectIndication to rectify the fault.

If the fault is rectified, go to Step 4.
If the fault persists, go to Step 2.

2. Perform the troubleshooting operations described in hwPWVcDown and hwSvcDown to rectify the fault.

If the fault is rectified, go to Step 4.
If the fault persists, go to Step 3.

3. Collect alarm information and configuration information, and then contact technical support personnel.

4. End.