MPLS-OAM_1.3.6.1.4.1.2011.5.12.7.1.2.1 hwMplsOamIgrLSPOutDefect

Trap Buffer Description

Ingress quit defect. (IfIndex=[IfIndex], TunnelName=[TunnelName], AvailableState=[AvailableState], DefectType=[DefectType])

The LSP fault checked by the OAM module on the source point was rectified.

Trap Attributes

Trap Attribute Description

Alarm or Event

Event

Trap Severity

Error

Mnemonic Code

hwMplsOamIgrLSPOutDefect

Trap OID

1.3.6.1.4.1.2011.5.12.7.1.2.1

MIB

HUAWEI-MPLSOAM-MIB

Alarm ID

This is an event trap and does not involve alarm ID.

Alarm Name

This is an event trap and does not involve alarm name.

Alarm Type

This is an event trap and does not involve alarm type.

Raise or Clear

This is an event trap and does not involve alarm generation or clearance.

Match trap

-

Trap Buffer Parameters

Parameter Description

IfIndex

Indicates the index of the tunnel.

TunnelName

Indicates the name of the tunnel.

AvailableState

Indicates the availability state of an OAM ingress: - 0: indicates that the ingress is available. - 1: indicates that the ingress is unavailable.

DefectType

Indicates the type of the defect: - 0: Indicates no defect. - 1: Indicates the server layer defect arising below the MPLS network layer. - 2: Indicates the peer maintenance entity defect arising outside the MPLS sub-network. - 3: Indicates the defect of the packet loss for the connectivity detection. - This defect occurs if no FDI packet is received from the server layer or lower level LSP, and no CV or FFD packet with expected TTSI is received. - For the LSP that is detected by the CV packet, the egress LSR does not receive the expected CV packet in 3 consecutive seconds. - For the LSP that is detected by the FFD packet, the egress LSR does not receive the expected FFD packet in any period of three consecutive intervals for sending the FFD packet. - If there is an incoming FDI packet from the server layer, the defect type is set to dServer; if there is an incoming FDI packet from the lower level LSP within the MPLS network, the defect type is set to dPeerMe. In both cases, no more defects occur on this LSP. - 4: The defect of mismatching TTSI. This defect occurs when unexpected and no expected TTSI is carried in the incoming CV or FFD packets. - For the LSP that is detected by the CV packet, the egress LSR receives the CV or FFD packet with unexpected TTSI in 3 seconds and does not receive the CV packet with the expected TTSI. - For the LSP that is detected by the FFD packet, the egress LSR receives the CV or FFD packet with unexpected TTSI in any period of three consecutive intervals and does not receive the FFD packet with expected TTSI. - 5: TTSI mismerge defect. - For the LSP that is detected by the CV packet, the egress LSR receives the CV or FFD packet with the unexpected TTSI and the CV packet with the expected TTSI in of 3 seconds. - For the LSP that is detected by the FFD packet, the egress LSR receives the CV or FFD packet with unexpected TTSI and the FFD packet with the expected FFD packet in any period of three consecutive intervals. - 6: Receiving excess rate of CV or FFD OAM packets. - For the LSP that is detected by the CV packet, the egress LSR receives five or more than five CV packets with expected TTSI in 3 seconds. - For the LSP that is detected by the FFD packet, the egress LSR receives five or more than five FFD packets with expected TTSI in the period of three consecutive intervals. - 7: An unknown defect that is detected in the MPLS layer and affects the user plane traffic. This defect is not detected by MPLS OAM; it is reported to MPLS OAM. - 8: OAM Ingress Down.

VB Parameters

VB OID VB Name VB Index

1.3.6.1.4.1.2011.5.12.7.1.1.2.1.1

hwMplsOamIgrIndex

hwMplsOamIgrIndex

1.3.6.1.4.1.2011.5.12.7.1.1.2.1.2

hwMplsOamIgrTunnName

hwMplsOamIgrIndex

1.3.6.1.4.1.2011.5.12.7.1.1.2.1.11

hwMplsOamIgrAvaState

hwMplsOamIgrIndex

1.3.6.1.4.1.2011.5.12.7.1.1.2.1.12

hwMplsOamIgrDefectType

hwMplsOamIgrIndex

Impact on the System

The OAM module will notify the message to the protection group and the traffic will be switched.

Possible Causes

The LSP fault checked by the OAM module on the source point was rectified.

Procedure

This log is informational only, and no action is required.
Copyright © Huawei Technologies Co., Ltd.
Copyright © Huawei Technologies Co., Ltd.
Next topic >