MPLS_LSPM_1.3.6.1.4.1.2011.5.25.121.2.1.87 hwMplsOamFDI

Trap Buffer Description

The tunnel receives an FDI alarm. (SessionTunnelId=[SessionTunnelId], LocalLspId=[LocalLspId], IngressLsrId=[IngressLsrId], EgressLsrId=[EgressLsrId], IfIndex=[IfIndex], TunnelName=[TunnelName], SignalingProtocol=[SgnlPrtcl], IfName=[IfName], SignalledTunnelName =[SignalledTunnelName])

An FDI alarm was generated on the tunnel.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Critical
Mnemonic Code	MPLS_TUNNEL_FDI
Trap OID	1.3.6.1.4.1.2011.5.25.121.2.1.87
MIB	HUAWEI-MPLS-EXTEND-MIB
Alarm ID	0x00010053
Alarm Name	hwMplsOamFDI
Alarm Type	communicationsAlarm
Raise or Clear	Raise
Match trap	MPLS_LSPM_1.3.6.1.4.1.2011.5.25.121.2.1.88 hwMplsOamFDIRecovery

Trap Buffer Parameters

Parameter	Description
SessionTunnelId	Tunnel Id
LocalLspId	Local Lsp Id
IngressLsrId	Ingress Lsr Id
EgressLsrId	Egress Lsr Id
IfIndex	Interface Index
TunnelName	Tunnel Name
SgnlPrtcl	Tunnel Signal Protocol Ranges: 1:RSVP 2:STATIC 3:CRSTATIC
IfName	Interface Name
TunnelDirection	Tunnel Direction
SignalledTunnelName	User-Defined Tunnel Name

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.121.1.1.1.29	hwMplsTunnelInterfaceName	hwMplsTunnelIndex hwMplsTunnelInstance hwMplsTunnelIngressLSRId hwMplsTunnelEgressLSRId
1.3.6.1.4.1.2011.5.25.121.1.1.1.30	hwMplsTunnelSignalProto	hwMplsTunnelIndex hwMplsTunnelInstance hwMplsTunnelIngressLSRId hwMplsTunnelEgressLSRId
1.3.6.1.4.1.2011.5.25.121.1.1.1.32	hwMplsTunnelDirection	hwMplsTunnelIndex hwMplsTunnelInstance hwMplsTunnelIngressLSRId hwMplsTunnelEgressLSRId
1.3.6.1.2.1.31.1.1.1.1	ifName	ifIndex
1.3.6.1.4.1.2011.5.25.121.1.1.1.33	hwMplsTunnelSignalledTunnelName	hwMplsTunnelIndex hwMplsTunnelInstance hwMplsTunnelIngressLSRId hwMplsTunnelEgressLSRId

Impact on the System

Services may be interrupted.

Possible Causes

The upstream P device detected a failure at the physical layer, for example, a fiber cut.

Procedure

1. Check that no fault (for example, optical fiber disconnect) occurs at the physical layer of each upstream node.

If such a fault does not exist, go to Step 3.
If such a fault exists, go to Step 2.

2. Rectify the fault on the physical layer of the upstream node by replacing the faulty component. Then check whether the alarm is cleared.

If the alarm is cleared, go to Step 4.
If the alarm persists, go to Step 3.

3. Collect log information and configuration information, and then contact technical support personnel.

4. End.