TPOAM_1.3.6.1.4.1.2011.5.25.235.1.5.21 hwMplsTpOamFarDualLossSD2

Trap Buffer Description

Signal Degraded threshold2 far-end alarm start. (MegId=[MegId], MegId=[Meg_Id], MeIndex=[MeIndex], MeType=[MeType], MeDirection=[MeDirection], IfName=[IfName], PeerIP=[PeerIP], VcId=[VcId], VcType=[VcType], RemoteIp=[RemoteIp], Ttl=[Ttl], MepId=[MepId], RemoteMepId=[RemoteMepId], CurrentLoss=[CurrentLoss], Threshold=[Threshold], LspName=[LspName], VsiName=[VsiName])

TP OAM detected that the number of frames lost on the RMEP exceeded the configured SD2 threshold.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Event
Trap Severity	Warning
Mnemonic Code	hwMplsTpOamFarDualLossSD2
Trap OID	1.3.6.1.4.1.2011.5.25.235.1.5.21
MIB	HUAWEI-TPOAM-MIB
Alarm ID	This is an event trap and does not involve alarm ID.
Alarm Name	This is an event trap and does not involve alarm name.
Alarm Type	This is an event trap and does not involve alarm type.
Raise or Clear	This is an event trap and does not involve alarm generation or clearance.
Match trap	-

Trap Buffer Parameters

Parameter	Description
MegId	Name of a MEG.
Meg_Id	Name of a MEG.
MeIndex	Index of an ME.
MeType	ME type: 1: PW VLL 2: PW VSI 3: TE -CR LSP 4: Section 5: Associate.
MeDirection	Tunnel type for an ME: ingress egress dual.
IfName	Interface name.
PeerIP	Peer IP address.
VcId	VC ID.
VcType	VC type.
RemoteIp	IP address of an RMEP.
Ttl	TTL value.
MepId	Local ME ID.
RemoteMepId	RMEP ID.
CurrentLoss	Current frame loss ratio.
Threshold	Frame loss alarm threshold.
LspName	LSP name.
VsiName	VSI name.

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.235.1.1.1.1.1	hwMplsTpOamMegId	hwMplsTpOamMegId
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.2	hwMplsTpOamMeType	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.3	hwMplsTpOamMeDirection	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.4	hwMplsTpOamMeIfName	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.5	hwMplsTpOamMePeerip	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.6	hwMplsTpOamMeVcId	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.7	hwMplsTpOamMeVcType	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.8	hwMplsTpOamMeVllRemotePeerIp	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.9	hwMplsTpOamMEVllTTL	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.10	hwMplsTpOamMeMepId	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.11	hwMplsTpOamMeRemoteMepId	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.4	hwMplsTpOamDualLossLossRatio	-
1.3.6.1.4.1.2011.5.25.235.1.1.1.1.14	hwMplsTpOamDualLossSD2Threshold	hwMplsTpOamMegId
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.13	hwMplsTpOamMeLspName	hwMplsTpOamMegId hwMplsTpOamMeIndex
1.3.6.1.4.1.2011.5.25.235.1.2.1.1.14	hwMplsTpOamMeVsiName	hwMplsTpOamMegId hwMplsTpOamMeIndex

Impact on the System

VPN service transmission on tunnels is not affected. If a tunnel protection group is configured, traffic will switch to the protection tunnel.

Possible Causes

The number of frames lost on the RMEP exceeded the configured SD2 threshold.

Procedure

1. Run the display current-configuration command to check whether the alarm threshold for frame LM is configured correctly.

If the alarm threshold for frame LM is configured correctly, go to Step 3.
If the alarm threshold for frame LM is not configured correctly, go to Step 2.

2. Collect log information and configuration information, and then contact technical support personnel.

3. End.