y1731 measure-granularity

Function

The y1731 measure-granularity command configures the granularity for Y.1731 statistics collection.

The undo y1731 measure-granularity command restores the default value.

By default, the granularity for Y.1731 statistics collection is port-vlan.

Format

y1731 measure-granularity { port | port-vlan }

undo y1731 measure-granularity

Parameters

Parameter	Description	Value
port	Indicates that Y.1731 statistics are collected based on a port.	-
port-vlan	Indicates that Y.1731 statistics are collected based on a port and all VLANs that the port joins.	-

Parameter

Description

Value

port

Indicates that Y.1731 statistics are collected based on a port.

port-vlan

Indicates that Y.1731 statistics are collected based on a port and all VLANs that the port joins.

Views

Layer 2 100GE interface view, 100ge sub-interface view, 100GE interface view, Layer 2 10GE interface view, 10GE sub-interface view, 10GE interface view, 200GE sub-interface view, 25GE-L2 view, 25GE sub-interface view, 400GE Layer 2 sub-interface view, 400GE-L2 view, 400GE sub-interface view, 400GE interface view, Layer 2 40GE interface view, 40GE sub-interface view, 40GE interface view, 50GE Layer 2 sub-interface view, Layer 2 50GE interface view, 50GE sub-interface view, 50GE interface view, Eth-Trunk Layer 2 sub-interface view, Eth-Trunk sub-interface view, Eth-Trunk interface view, FlexE sub-interface view, GE Layer 2 sub-interface view, Layer 2 GE interface view, GE optical interface view, GE sub-interface view, GE electrical interface view, Global-VE layer2 subinterface view, Global VE sub-interface view, VE layer2 subinterface view, VE sub-interface view, Layer 2 sub-interface view

Default Level

2: Configuration level

Task Name and Operations

Task Name	Operations
y1731	write

Usage Guidelines

Usage Scenario

In VLL or VPLS networking, to configure the granularity for Y.1731 statistics collection on the AC interface of a PW, run the y1731 measure-granularity command. You can specify either of the following parameters on the AC interface as needed:

To configure a port as the granularity for Y.1731 statistics collection, specify the port parameter. Statistics about all services on the port are collected.
To configure a port and all VLANs that the port joins as the granularity for Y.1731 statistics collection, specify the port-vlan parameter. Statistics about specified services on the port are collected.

Prerequisites

A MEP has been created using the mep mep-id command in the interface view.

Example

# Configure GE 0/1/1 as the granularity for Y.1731 statistics collection.

<HUAWEI> system-view
[~HUAWEI] mpls
[*HUAWEI-mpls] quit
[*HUAWEI] mpls l2vpn
[*HUAWEI-l2vpn] mpls ldp
[*HUAWEI-mpls-ldp] quit
[*HUAWEI] mpls ldp remote-peer pe2
[*HUAWEI-ldp-remote-pe2] remote-ip 2.2.2.2
[*HUAWEI-ldp-remote-pe2] vsi y1731 static
[*HUAWEI-vsi-y1731] pwsignal ldp
[*HUAWEI-vsi-y1731] vsi-id 220
[*HUAWEI-vsi-y1731] peer 2.2.2.2
[*HUAWEI-vsi-y1731] quit
[*HUAWEI] interface GigabitEthernet 0/1/0.1
[*HUAWEI-GigabitEthernet0/1/0.1] vlan-type dot1q 200
[*HUAWEI-GigabitEthernet0/1/0.1] l2 binding vsi y1731
[*HUAWEI-GigabitEthernet0/1/0.1] quit
[*HUAWEI] cfm enable
[*HUAWEI] cfm md md1
[*HUAWEI-md-md1] ma ma1
[*HUAWEI-md-md1-ma-ma1] map vsi y1731
[*HUAWEI-md-md1-ma-ma1] mep mep-id 1 interface GigabitEthernet0/1/0.1 inward
[*HUAWEI-md-md1-ma-ma1] mep ccm-send mep-id 1 enable
[*HUAWEI-md-md1-ma-ma1] remote-mep mep-id 2
[*HUAWEI-md-md1-ma-ma1] remote-mep ccm-receive mep-id 2 enable
[*HUAWEI-md-md1-ma-ma1] quit
[*HUAWEI-md-md1] quit
[*HUAWEI] interface GigabitEthernet 0/1/0.1
[*HUAWEI-GigabitEthernet0/1/0.1] y1731 measure-granularity port