Example for Configuring MVPNv6 over BIERv6 Dual-Root 1+1 Protection
This section describes how to configure MVPNv6 over BIERv6 dual-root 1+1 protection. In this example, the unicast network type is EVPN L3VPNv6 over SRv6. Configuring multicast services on other types of unicast networks is similar to this procedure.
Networking Requirements
In Figure 1, EVPN L3VPNv6 over SRv6 has been deployed. CE1 is dual-homed to the public network in active-active mode. It is required that MVPNv6 over BIERv6 services and dual-root 1+1 protection be deployed on the existing network.
Configuration Roadmap
The configuration roadmap is as follows:
(Optional) Configure EVPN L3VPNv6 over SRv6 and ensure that the unicast VPN runs properly. If the unicast network has been configured, skip this step.
Configure basic BIERv6 functions and enable IS-ISv6 for BIERv6 on Root1, Root2, P1, P2, and PE1.
Establish a BGP MVPN peer relationship between Root1 and PE1 and between Root2 and PE1.
- Configure multicast traffic forwarding over two BIERv6 I-PMSI tunnels.
- Enable the BIERv6 S-PMSI tunnel function and configure switching criteria.
Enable PIM on Root1, Root2, and PE1.
- Configure dual-root 1+1 protection.
Data Preparation
To complete the configuration, you need the following data:
- Addresses of key interfaces on each device, as shown in Figure 1
- ID (1) of the public network IS-IS process, in a Level-2 area
- VPN instance name (VPNA) on Root1, Root2, and PE1
- PE1's BFR-ID (1), sub-domain ID (0), BSL (256), and Max-SI (0)
Procedure
- (Optional) Configure L3VPNv6 over SRv6.
This step is a part of configuring the unicast network, and its content is for reference only. In most cases, the unicast network has been configured before multicast services are deployed. If this is the case, skip this step and contact the configuration personnel for the configuration data related to the multicast services. For details about how to configure a unicast network, see Segment Routing IPv6 Configuration in the Configuration Guide.
# Enable IPv6 forwarding on each interface and configure an IPv6 address for each interface. The configuration of Root1 is used as an example. The configurations of Root2, P1, P2, and PE1 are similar to the configuration of Root1. For configuration details, see Configuration Files in this section. Similar details will be omitted in the rest of the document.
<HUAWEI> system-view [~HUAWEI] sysname Root1 [*HUAWEI] commit [~Root1] interface gigabitethernet 0/1/0 [~Root1-GigabitEthernet0/1/0] ipv6 enable [*Root1-GigabitEthernet0/1/0] ipv6 address 2001:DB8:3::1 112 [*Root1-GigabitEthernet0/1/0] quit [*Root1] interface LoopBack 1 [*Root1-LoopBack1] ipv6 enable [*Root1-LoopBack1] ipv6 address 2001:db8:111::1 128 [*Root1-LoopBack1] quit [*Root1] commit
# Configure IS-IS. The configuration of Root1 is used as an example. The configurations of Root2, P1, P2, and PE1 are similar to the configuration of Root1.
[~Root1] isis 1 [*Root1-isis-1] is-level level-2 [*Root1-isis-1] cost-style wide [*Root1-isis-1] network-entity 10.0000.0000.0001.00 [*Root1-isis-1] ipv6 enable topology ipv6 [*Root1-isis-1] quit [*Root1] interface gigabitethernet 0/1/0 [*Root1-GigabitEthernet0/1/0] isis ipv6 enable 1 [*Root1-GigabitEthernet0/1/0] quit [*Root1] interface loopback1 [*Root1-LoopBack1] isis ipv6 enable 1 [*Root1-LoopBack1] commit [~Root1-LoopBack1] quit
# Configure a VPN instance on PEs, enable the IPv6 L3VPN address family for the instance, and bind the interfaces that connect the PEs to a CE to the VPN instance. The configuration of Root1 is used as an example. The configurations of Root2 and PE1 are similar to the configuration of Root1. The vpn-target evpn and advertise l2vpn evpn commands allow EVPN routes to be used in an L3VPN and must be configured on an EVPN L3VPN network.
[~Root1] multicast ipv6 mvpn ipv6-underlay 2001:db8:111::1 [*Root1] ip vpn-instance VPNA [*Root1-vpn-instance-VPNA] ipv6-family [*Root1-vpn-instance-VPNA-af-ipv6] route-distinguisher 100:1 [*Root1-vpn-instance-VPNA-af-ipv6] vpn-target 111:1 both evpn [*Root1-vpn-instance-VPNA-af-ipv6] multicast ipv6 routing-enable [*Root1-vpn-instance-VPNA-af-ipv6] mvpn [*Root1-vpn-instance-VPNA-af-ipv6-mvpn] vpn-target 111:1 both [*Root1-vpn-instance-VPNA-af-ipv6-mvpn] quit [*Root1-vpn-instance-VPNA-af-ipv6] quit [*Root1-vpn-instance-VPNA] quit [*Root1] interface gigabitethernet 0/1/1 [*Root1-GigabitEthernet0/1/1] ip binding vpn-instance VPNA [*Root1-GigabitEthernet0/1/1] ipv6 enable [*Root1-GigabitEthernet0/1/1] ipv6 address 2001:DB8:1::2 112 [*Root1-GigabitEthernet0/1/1] quit [~Root1] bgp 100 [*Root1-bgp] router-id 1.1.1.1 [*Root1-bgp] ipv6-family vpn-instance VPNA [*Root1-bgp-6-VPNA] import-route direct [*Root1-bgp-6-VPNA] advertise l2vpn evpn [*Root1-bgp-6-VPNA] quit [*Root1-bgp] quit [*Root1] commit
# Establish an EBGP peer relationship between each PE/root and the corresponding CE. The peer relationship establishment between Root1 and CE1 is used as an example. The peer relationship establishment between Root2 and CE1, and between PE1 and CE2 is similar to that between Root1 and CE1.
Establish an EBGP peer relationship on CE1.
[*CE1] interface gigabitethernet 0/1/1 [*CE1-GigabitEthernet0/1/1] ipv6 enable [*CE1-GigabitEthernet0/1/1] ipv6 address 2001:DB8:2::1 112 [*CE1-GigabitEthernet0/1/1] quit [*CE1] bgp 65410 [*CE1-bgp] router-id 11.11.11.11 [*CE1-bgp] peer 2001:DB8:1::2 as-number 100 [*CE1-bgp] ipv6-family unicast [*CE1-bgp-af-ipv6] peer 2001:DB8:1::2 enable [*CE1-bgp-af-ipv6] import-route direct [*CE1-bgp-af-ipv6] quit [*CE1-bgp-af] quit [*CE1] commit
Establish an EBGP peer relationship on Root1.
[~Root1] bgp 100 [*Root1-bgp] ipv6-family vpn-instance VPNA [*Root1-bgp-6-VPNA] peer 2001:DB8:1::1 as-number 65410 [*Root1-bgp-6-VPNA] commit [*Root1-bgp-6-VPNA] quit [*Root1-bgp] quit
# Establish an MP-IBGP peer relationship between Root1 and PE1 and between Root2 and PE1. The configuration of Root1 is used as an example. The configurations of Root2 and PE1 are similar to the configuration of Root1. After you run the peer enable command, enter Y at the system prompt to confirm the action.
[~Root1] bgp 100 [~Root1-bgp] peer 2001:db8:115::1 as-number 100 [*Root1-bgp] peer 2001:db8:115::1 connect-interface loopback 1 [*Root1-bgp] l2vpn-family evpn [*Root1-bgp-af-evpn] peer 2001:db8:115::1 enable [*Root1-bgp-af-evpn] commit [~Root1-bgp-af-evpn] quit [~Root1-bgp] quit
# Configure SRv6 SIDs, and configure PEs to add SIDs to the VPN routes to be advertised. The configurations of Root1 and P1 are used as an example. The configurations of Root2 and PE1 are similar to the configuration of Root1, and the configurations of P2 are similar to the configurations of P1. The encapsulation source-address command does not need to be run on PE1.
[~Root1] segment-routing ipv6 [*Root1-segment-routing-ipv6] encapsulation source-address 2001:db8:111::1 [*Root1-segment-routing-ipv6] locator Root1 ipv6-prefix 2001:db8:11:: 64 static 32 [*Root1-segment-routing-ipv6-locator] quit [*Root1-segment-routing-ipv6] quit [*Root1] bgp 100 [*Root1-bgp] l2vpn-family evpn [*Root1-bgp-af-evpn] peer 2001:db8:115::1 advertise encap-type srv6 [*Root1-bgp-af-evpn] quit [*Root1-bgp] ipv6-family vpn-instance VPNA [*Root1-bgp-6-VPNA] segment-routing ipv6 best-effort evpn [*Root1-bgp-6-VPNA] segment-routing ipv6 locator Root1 evpn [*Root1-bgp-6-VPNA] commit [~Root1-bgp-6-VPNA] quit [~Root1-bgp] quit [~Root1] isis 1 [~Root1-isis-1] segment-routing ipv6 locator Root1 auto-sid-disable [*Root1-isis-1] commit [~Root1-isis-1] quit [~P1] segment-routing ipv6 [*P1-segment-routing-ipv6] encapsulation source-address 2001:db8:113::1 [*P1-segment-routing-ipv6] locator P1 ipv6-prefix 2001:db8:13:: 64 static 32 [*P1-segment-routing-ipv6-locator] quit [*P1-segment-routing-ipv6] quit [*P1] isis 1 [*P1-isis-1] segment-routing ipv6 locator P1 auto-sid-disable [*P1-isis-1] commit [~P1-isis-1] quit
# Perform other unicast network configurations based on unicast service requirements.
- Configure basic BIERv6 functions and enable IS-ISv6 for BIERv6 on Root1, Root2, P1, P2, and PE1.# Configure Root1.
[~Root1] bier [*Root1-bier] sub-domain 0 ipv6 [*Root1-bier-sub-domain-0-ipv6] bfr-id 2 [*Root1-bier-sub-domain-0-ipv6] encapsulation-type ipv6 bsl 256 max-si 0 [*Root1-bier-sub-domain-0-ipv6] bfr-prefix interface loopback1 [*Root1-bier-sub-domain-0-ipv6] end-bier locator Root1 sid 2001:db8:11::1 [*Root1-bier-sub-domain-0-ipv6] protocol isis [*Root1-bier-sub-domain-0-ipv6] quit [*Root1-bier] quit [*Root1] isis 1 [*Root1-isis-1] bier enable [*Root1-isis-1] quit [*Root1] commit
# Configure Root2.[~Root2] bier [*Root2-bier] sub-domain 0 ipv6 [*Root2-bier-sub-domain-0-ipv6] bfr-id 3 [*Root2-bier-sub-domain-0-ipv6] encapsulation-type ipv6 bsl 256 max-si 0 [*Root2-bier-sub-domain-0-ipv6] bfr-prefix interface loopback1 [*Root2-bier-sub-domain-0-ipv6] end-bier locator Root2 sid 2001:db8:12::1 [*Root2-bier-sub-domain-0-ipv6] protocol isis [*Root2-bier-sub-domain-0-ipv6] quit [*Root2-bier] quit [*Root2] isis 1 [*Root2-isis-1] bier enable [*Root2-isis-1] quit [*Root2] commit
# Configure P1.[~P1] bier [*P1-bier] sub-domain 0 ipv6 [*P1-bier-sub-domain-0-ipv6] encapsulation-type ipv6 bsl 256 max-si 0 [*P1-bier-sub-domain-0-ipv6] bfr-prefix interface loopback1 [*P1-bier-sub-domain-0-ipv6] end-bier locator P1 sid 2001:db8:13::1 [*P1-bier-sub-domain-0-ipv6] protocol isis [*P1-bier-sub-domain-0-ipv6] quit [*P1-bier] quit [*P1] isis 1 [*P1-isis-1] bier enable [*P1-isis-1] quit [*P1] commit
# Configure P2.[~P2] bier [*P2-bier] sub-domain 0 ipv6 [*P2-bier-sub-domain-0-ipv6] encapsulation-type ipv6 bsl 256 max-si 0 [*P2-bier-sub-domain-0-ipv6] bfr-prefix interface loopback1 [*P2-bier-sub-domain-0-ipv6] end-bier locator P2 sid 2001:db8:14::1 [*P2-bier-sub-domain-0-ipv6] protocol isis [*P2-bier-sub-domain-0-ipv6] quit [*P2-bier] quit [*P2] isis 1 [*P2-isis-1] bier enable [*P2-isis-1] quit [*P2] commit
# Configure PE1.[~PE1] bier [*PE1-bier] sub-domain 0 ipv6 [*PE1-bier-sub-domain-0-ipv6] bfr-id 1 [*PE1-bier-sub-domain-0-ipv6] encapsulation-type ipv6 bsl 256 max-si 0 [*PE1-bier-sub-domain-0-ipv6] bfr-prefix interface loopback1 [*PE1-bier-sub-domain-0-ipv6] end-bier locator PE1 sid 2001:db8:15::1 [*PE1-bier-sub-domain-0-ipv6] protocol isis [*PE1-bier-sub-domain-0-ipv6] quit [*PE1-bier] quit [*PE1] isis 1 [*PE1-isis-1] bier enable [*PE1-isis-1] quit [*PE1] commit
- Establish a BGP MVPN peer relationship between Root1 and PE1 and between Root2 and PE1.
# Configure Root1.
[~Root1] bgp 100 [~Root1-bgp] ipv6-family mvpn [*Root1-bgp-af-mvpn6] peer 2001:db8:115::1 enable [*Root1-bgp-af-mvpn6] quit [*Root1-bgp] quit [*Root1] commit
# Configure Root2.
[~Root2] bgp 100 [~Root2-bgp] ipv6-family mvpn [*Root2-bgp-af-mvpnv6] peer 2001:db8:115::1 enable [*Root2-bgp-af-mvpnv6] quit [*Root2-bgp] quit [*Root2] commit
# Configure PE1.
[~PE1] bgp 100 [~PE1-bgp] ipv6-family mvpn [*PE1-bgp-af-mvpnv6] peer 2001:db8:111::1 enable [*PE1-bgp-af-mvpnv6] peer 2001:db8:112::1 enable [*PE1-bgp-af-mvpn6] quit [*PE1-bgp] quit [*PE1] commit
# Display information about BGP MVPN peers. The command output shows that a BGP MVPN peer relationship has been established between PE1 and Root1 and between PE1 and Root2.
[~PE1] display bgp mvpn vpnv6 all peer BGP local router ID : 1.1.1.5 Local AS number : 100 Total number of peers : 2 Peers in established state : 2 Peer V AS MsgRcvd MsgSent OutQ Up/Down State PrefRcv 2001:DB8:111::1 4 100 41 43 0 00:08:08 Established 0 2001:DB8:112::1 4 100 29 32 0 00:07:15 Established 0
- Configure multicast traffic forwarding over two BIERv6 I-PMSI tunnels.
# Configure Root1.
[~Root1] ip vpn-instance VPNA [*Root1-vpn-instance-VPNA] ipv6-family [*Root1-vpn-instance-VPNA-af-ipv6] mvpn [*Root1-vpn-instance-VPNA-af-ipv6-mvpn] sender-enable [*Root1-vpn-instance-VPNA-af-ipv6-mvpn] ipv6 underlay enable [*Root1-vpn-instance-VPNA-af-ipv6-mvpn] src-dt6 locator Root1 sid 2001:db8:11::2 [*Root1-vpn-instance-VPNA-af-ipv6-mvpn] ipmsi-tunnel [*Root1-vpn-instance-VPNA-af-ipv6-mvpn-ipmsi] bier sub-domain 0 bsl 256 [*Root1-vpn-instance-VPNA-af-ipv6-mvpn-ipmsi] quit [*Root1-vpn-instance-VPNA-af-ipv6-mvpn] quit [*Root1-vpn-instance-VPNA-af-ipv6] quit [*Root1-vpn-instance-VPNA] quit [*Root1] commit
# Configure Root2.
[~Root2] ip vpn-instance VPNA [*Root2-vpn-instance-VPNA] ipv6-family [*Root2-vpn-instance-VPNA-af-ipv6] multicast ipv6 routing-enable [*Root2-vpn-instance-VPNA-af-ipv6] mvpn [*Root2-vpn-instance-VPNA-af-ipv6-mvpn] sender-enable [*Root2-vpn-instance-VPNA-af-ipv6-mvpn] ipv6 underlay enable [*Root2-vpn-instance-VPNA-af-ipv6-mvpn] src-dt6 locator Root2 sid 2001:db8:12::2 [*Root2-vpn-instance-VPNA-af-ipv6-mvpn] ipmsi-tunnel [*Root2-vpn-instance-VPNA-af-ipv6-mvpn-ipmsi] bier sub-domain 0 bsl 256 [*Root2-vpn-instance-VPNA-af-ipv6-mvpn-ipmsi] quit [*Root2-vpn-instance-VPNA-af-ipv6-mvpn] quit [*Root2-vpn-instance-VPNA-af-ipv6] quit [*Root2-vpn-instance-VPNA] quit [*Root2] commit
# Configure PE1.
[~PE1] ip vpn-instance VPNA [*PE1-vpn-instance-VPNA] ipv6-family [*PE1-vpn-instance-VPNA-af-ipv6] multicast ipv6 routing-enable [*PE1-vpn-instance-VPNA-af-ipv6] mvpn [*PE1-vpn-instance-VPNA-af-ipv6-mvpn] c-multicast signaling bgp [*PE1-vpn-instance-VPNA-af-ipv6-mvpn] ipv6 underlay enable [*PE1-vpn-instance-VPNA-af-ipv6-mvpn] quit [*PE1-vpn-instance-VPNA-af-ipv6] quit [*PE1-vpn-instance-VPNA] quit [*PE1] commit
# Display I-PMSI tunnel information of a specified VPN instance. The command output shows that two I-PMSI tunnels have been established, with Root1 and Root2 as the root nodes and PE1 as a leaf node.
[~PE1]display mvpn ipv6 vpn-instance VPNA ipmsi MVPN local I-PMSI information for VPN-Instance: VPNA Tunnel type: BIER IPv6 Tunnel state: -- Src-dt6 SID: 2001:DB8:11::2 Sub-domain ID: 0 BFR-ID: -- BFR prefix: 2001:DB8:111::1 Root: 2001:DB8:111::1 Leaf: 1: 2001:DB8:115::1 (BFR-ID: 1, BFR prefix: 2001:DB8:115::1) (local) Tunnel type: BIER IPv6 Tunnel state: -- Src-dt6 SID: 2001:DB8:12::2 Sub-domain ID: 0 BFR-ID: -- BFR prefix: 2001:DB8:112::1 Root: 2001:DB8:112::1 Leaf: 1: 2001:DB8:115::1 (BFR-ID: 1, BFR prefix: 2001:DB8:115::1) (local)
- Enable the BIERv6 S-PMSI tunnel function and configure switching criteria.
# Configure Root1.
[~Root1] ip vpn-instance VPNA [*Root1-vpn-instance-VPNA] ipv6-family [*Root1-vpn-instance-VPNA-af-ipv6] mvpn [*Root1-vpn-instance-VPNA-af-ipv6-mvpn] spmsi-tunnel [*Root1-vpn-instance-VPNA-af-ipv6-mvpn-spmsi] group FF3E::0 112 source 2001:db8:555::0 112 threshold 10 bier [*Root1-vpn-instance-VPNA-af-ipv6-mvpn-spmsi] switch-delay 20 [*Root1-vpn-instance-VPNA-af-ipv6-mvpn-spmsi] holddown-time 80 [*Root1-vpn-instance-VPNA-af-ipv6-mvpn-spmsi] quit [*Root1-vpn-instance-VPNA-af-ipv6-mvpn] quit [*Root1-vpn-instance-VPNA-af-ipv6] quit [*Root1-vpn-instance-VPNA] quit [*Root1] commit
# Configure Root2.
[~Root2] ip vpn-instance VPNA [*Root2-vpn-instance-VPNA] ipv6-family [*Root2-vpn-instance-VPNA-af-ipv6] mvpn [*Root2-vpn-instance-VPNA-af-ipv6-mvpn] spmsi-tunnel [*Root2-vpn-instance-VPNA-af-ipv6-mvpn-spmsi] group FF3E::0 112 source 2001:db8:555::0 112 threshold 10 bier [*Root2-vpn-instance-VPNA-af-ipv6-mvpn-spmsi] switch-delay 20 [*Root2-vpn-instance-VPNA-af-ipv6-mvpn-spmsi] holddown-time 80 [*Root2-vpn-instance-VPNA-af-ipv6-mvpn-spmsi] quit [*Root2-vpn-instance-VPNA-af-ipv6-mvpn] quit [*Root2-vpn-instance-VPNA-af-ipv6] quit [*Root2-vpn-instance-VPNA] quit [*Root2] commit
- Enable PIM on Root1, Root2, and PE1.
# Configure Root1.
[~Root1] interface gigabitethernet 0/1/1 [~Root1-GigabitEthernet0/1/1] pim ipv6 sm [*Root1-GigabitEthernet0/1/1] quit [*Root1] commit
# Configure Root2.
[~Root2] interface gigabitethernet 0/1/1 [~Root2-GigabitEthernet0/1/1] pim ipv6 sm [*Root2-GigabitEthernet0/1/1] quit [*Root2] commit
# Configure PE1.
[~PE1] interface gigabitethernet 0/1/1 [~PE1-GigabitEthernet0/1/1] pim ipv6 sm [*PE1-GigabitEthernet0/1/1] quit [*PE1] commit
- Configure dual-root 1+1 protection.
# Configure VPN FRR on PE1.
[~PE1] ip vpn-instance VPNA [~PE1-vpn-instance-VPNA] ipv6-family [~PE1-vpn-instance-VPNA-af-ipv6] vpn frr [*PE1-vpn-instance-VPNA-af-ipv6] quit [*PE1-vpn-instance-VPNA] quit [*PE1] commit
# Configure C-multicast FRR in flow-based detection mode on PE1.
[~PE1] acl ipv6 2111 [*PE1-acl6-basic-2111] rule permit source any [*PE1-acl6-basic-2111] quit [*PE1] ip vpn-instance VPNA [*PE1-vpn-instance-VPNA] ipv6-family [*PE1-vpn-instance-VPNA-af-ipv6] mvpn [*PE1-vpn-instance-VPNA-af-ipv6-mvpn] c-multicast frr [*PE1-vpn-instance-VPNA-af-ipv6-mvpn] c-multicast frr flow-detection-based 2111 [*PE1-vpn-instance-VPNA-af-ipv6-mvpn] multicast wtr 100 [*PE1-vpn-instance-VPNA-af-ipv6-mvpn] quit [*PE1-vpn-instance-VPNA-af-ipv6] quit [*PE1-vpn-instance-VPNA] quit [*PE1] commit
# Display S-PMSI tunnel information of a specified VPN instance. The command output on PE1 shows the S-PMSI tunnel and (S, G) information.
[~PE1]display mvpn ipv6 vpn-instance VPNA spmsi verbose MVPN local S-PMSI information for VPN-Instance : VPNA Total number of tunnel: 2 S-PMSI A-D Route Type: -- Tunnel type: BIER IPv6 Tunnel state: -- Src-dt6 SID: 2001:DB8:11::1 Sub-domain ID: 0 BFR-ID: -- BFR prefix: 2001:DB8:111::1 Root: 2001:DB8:111::1 Leaf: 1: 2001:DB8:115::1 (BFR-ID: 2, BFR prefix: 2001:DB8:115::1)(local) Total number of (S, G): 2 1. (2001:db8:555::0, FF3E::3) 2. (2001:db8:555::0, FF3E::4) Total number of tunnel: 2 S-PMSI A-D Route Type: -- Tunnel type: BIER IPv6 Tunnel state: -- Src-dt6 SID: 2001:DB8:12::1 Sub-domain ID: 0 BFR-ID: -- BFR prefix: 2001:DB8:112::1 Root: 2001:DB8:112::1 Leaf: 1: 2001:DB8:115::1 (BFR-ID: 2, BFR prefix: 2001:DB8:115::1)(local) Total number of (S, G): 2 1. (2001:db8:555::0, FF3E::3) 2. (2001:db8:555::0, FF3E::4) - Verify the configuration.
# Run the display pim ipv6 vpn-instance routing-table command to check the IPv6 PIM routing table. The command output shows that a backup upstream interface exists.
[~PE1] display pim ipv6 all-instance routing-table mode sm outgoing-interface-number VPN-Instance: VPNA Total 0 (*, G) entries; 2 (S, G) entry (2001:db8:555::0, FF3E::1) Protocol: pim-sm, Flag: SG_RCVRR UpTime: 00:00:04 Upstream interface: through-BGP, Refresh time: 00:00:04 Upstream neighbor: 2001:DB8:111::1 RPF prime neighbor: 2001:DB8:111::1 Backup upstream interface: through-BGP Upstream neighbor: 2001:DB8:112::1 RPF prime neighbor: 2001:DB8:112::1 Downstream interface(s) information: Total number of downstreams: 1 (2001:db8:555::0, FF3E::2) Protocol: pim-sm, Flag: SG_RCVR UpTime: 00:00:05 Upstream interface: Register, Refresh time: 00:00:05 Upstream neighbor: NULL RPF prime neighbor: NULL Backup upstream interface: through-BGP Upstream neighbor: 2001:DB8:112::1 RPF prime neighbor: 2001:DB8:112::1 Downstream interface(s) information: Total number of downstreams: 1
Configuration Files
CE1 configuration file
# sysname CE1 # multicast ipv6 routing-enable # interface GigabitEthernet0/1/0 undo shutdown ipv6 enable ipv6 address 2001:DB8:1::1/112 pim ipv6 sm # interface GigabitEthernet0/1/1 undo shutdown ipv6 enable ipv6 address 2001:DB8:2::1/112 pim ipv6 sm # bgp 65410 router-id 11.11.11.11 peer 2001:DB8:1::2 as-number 100 peer 2001:DB8:2::2 as-number 100 # ipv6-family unicast undo synchronization import-route direct peer 2001:DB8:1::2 enable peer 2001:DB8:2::2 enable # return
CE2 configuration file
# sysname CE2 # multicast ipv6 routing-enable # interface GigabitEthernet0/1/0 undo shutdown ipv6 enable ipv6 address 2001:DB8:9::2/112 pim ipv6 sm mld enable # interface GigabitEthernet0/1/1 undo shutdown ipv6 enable ipv6 address 2001:DB8:7::2/112 pim ipv6 sm # bgp 65411 router-id 12.12.12.12 peer 2001:DB8:7::1 as-number 100 # ipv6-family unicast undo synchronization import-route direct peer 2001:DB8:7::1 enable # return
Root1 configuration file
#
sysname Root1
#
multicast ipv6 mvpn ipv6-underlay 2001:DB8:111::1
#
ip vpn-instance VPNA
ipv6-family
route-distinguisher 100:1
apply-label per-instance
vpn-target 111:1 export-extcommunity evpn
vpn-target 111:1 export-extcommunity
vpn-target 111:1 import-extcommunity evpn
vpn-target 111:1 import-extcommunity
multicast ipv6 routing-enable
mvpn
ipv6 underlay enable
sender-enable
src-dt6 locator Root1 sid 2001:DB8:11::2
ipmsi-tunnel
bier
spmsi-tunnel
holddown-time 80
switch-delay 20
group FF3E::0 112 source 2001:DB8:555::0 112 threshold 10 bier
#
segment-routing ipv6
encapsulation source-address 2001:DB8:111::1
locator Root1 ipv6-prefix 2001:DB8:11:: 64 static 32
#
isis 1
is-level level-2
cost-style wide
network-entity 10.0000.0000.0001.00
bier enable
#
ipv6 enable topology ipv6
segment-routing ipv6 locator Root1 auto-sid-disable
#
#
interface GigabitEthernet0/1/0
undo shutdown
ipv6 enable
ipv6 address 2001:DB8:3::1/112
isis ipv6 enable 1
#
interface GigabitEthernet0/1/1
undo shutdown
ip binding vpn-instance VPNA
ipv6 enable
ipv6 address 2001:DB8:1::2/112
pim ipv6 sm
#
interface LoopBack1
ipv6 enable
ipv6 address 2001:DB8:111::1/128
isis ipv6 enable 1
#
bgp 100
router-id 1.1.1.1
peer 2001:DB8:115::1 as-number 100
peer 2001:DB8:115::1 connect-interface LoopBack1
#
ipv4-family unicast
undo synchronization
#
ipv6-family mvpn
policy vpn-target
peer 2001:DB8:115::1 enable
#
ipv6-family vpn-instance VPNA
import-route direct
advertise l2vpn evpn
segment-routing ipv6 locator Root1 evpn
segment-routing ipv6 best-effort evpn
peer 2001:DB8:1::1 as-number 65410
#
l2vpn-family evpn
policy vpn-target
peer 2001:DB8:115::1 enable
peer 2001:DB8:115::1 advertise encap-type srv6
#
bier
sub-domain 0 ipv6
bfr-id 2
bfr-prefix interface LoopBack1
protocol isis
end-bier locator Root1 sid 2001:DB8:11::1
encapsulation-type ipv6 bsl 256 max-si 0
#
return
Root2 configuration file
#
sysname Root2
#
multicast ipv6 mvpn ipv6-underlay 2001:DB8:112::1
#
ip vpn-instance VPNA
ipv6-family
route-distinguisher 100:1
apply-label per-instance
vpn-target 111:1 export-extcommunit evpn
vpn-target 111:1 import-extcommunit evpn
multicast ipv6 routing-enable
mvpn
vpn-target 111:1 export-extcommunity
vpn-target 111:1 import-extcommunity
ipv6 underlay enable
sender-enable
src-dt6 locator Root2 sid 2001:DB8:12::2
ipmsi-tunnel
bier
spmsi-tunnel
holddown-time 80
switch-delay 20
group FF3E::0 112 source 2001:DB8:555::0 112 threshold 10 bier
#
segment-routing ipv6
encapsulation source-address 2001:DB8:112::1
locator Root2 ipv6-prefix 2001:DB8:12:: 64 static 32
#
isis 1
is-level level-2
cost-style wide
network-entity 10.0000.0000.0002.00
bier enable
#
ipv6 enable topology ipv6
segment-routing ipv6 locator Root2 auto-sid-disable
#
#
interface GigabitEthernet0/1/0
undo shutdown
ipv6 enable
ipv6 address 2001:DB8:4::1/112
isis ipv6 enable 1
#
interface GigabitEthernet0/1/1
undo shutdown
ipv6 enable
ip binding vpn-instance VPNA
ipv6 address 2001:DB8:2::2/112
pim ipv6 sm
#
interface LoopBack1
ipv6 enable
ipv6 address 2001:DB8:112::1/128
isis ipv6 enable 1
#
bgp 100
router-id 1.1.1.2
peer 2001:DB8:115::1 as-number 100
peer 2001:DB8:115::1 connect-interface LoopBack1
#
ipv4-family unicast
undo synchronization
#
ipv6-family mvpn
policy vpn-target
peer 2001:DB8:115::1 enable
#
ipv6-family vpn-instance VPNA
import-route direct
advertise l2vpn evpn
segment-routing ipv6 locator Root2 evpn
segment-routing ipv6 best-effort evpn
peer 2001:DB8:2::1 as-number 65410
#
l2vpn-family evpn
policy vpn-target
peer 2001:DB8:115::1 enable
peer 2001:DB8:115::1 advertise encap-type srv6
#
bier
sub-domain 0 ipv6
bfr-id 3
bfr-prefix interface LoopBack1
protocol isis
end-bier locator Root2 sid 2001:DB8:12::1
encapsulation-type ipv6 bsl 256 max-si 0
#
return
P1 configuration file
# sysname P1 # segment-routing ipv6 encapsulation source-address 2001:DB8:113::1 locator P1 ipv6-prefix 2001:DB8:13:: 64 static 32 # isis 1 is-level level-2 cost-style wide network-entity 10.0000.0000.0003.00 bier enable # ipv6 enable topology ipv6 segment-routing ipv6 locator P1 auto-sid-disable # # interface GigabitEthernet0/1/0 undo shutdown ipv6 enable ipv6 address 2001:DB8:3::2/112 isis ipv6 enable 1 # interface GigabitEthernet0/1/1 undo shutdown ipv6 enable ipv6 address 2001:DB8:5::1/112 isis ipv6 enable 1 # interface LoopBack1 ipv6 enable ipv6 address 2001:DB8:113::1/128 isis ipv6 enable 1 # bier sub-domain 0 ipv6 bfr-prefix interface LoopBack1 protocol isis end-bier locator P1 sid 2001:DB8:13::1 encapsulation-type ipv6 bsl 256 max-si 0 # return
P2 configuration file
# sysname P2 # segment-routing ipv6 encapsulation source-address 2001:DB8:114::1 locator P2 ipv6-prefix 2001:DB8:14:: 64 static 32 # isis 1 is-level level-2 cost-style wide network-entity 10.0000.0000.0004.00 bier enable # ipv6 enable topology ipv6 segment-routing ipv6 locator P2 auto-sid-disable # # interface GigabitEthernet0/1/0 undo shutdown ipv6 enable ipv6 address 2001:DB8:4::2/112 isis ipv6 enable 1 # interface GigabitEthernet0/1/1 undo shutdown ipv6 enable ipv6 address 2001:DB8:6::1/112 isis ipv6 enable 1 # interface LoopBack1 ipv6 enable ipv6 address 2001:DB8:114::1/128 isis ipv6 enable 1 # bier sub-domain 0 ipv6 bfr-prefix interface LoopBack1 protocol isis end-bier locator P2 sid 2001:DB8:14::1 encapsulation-type ipv6 bsl 256 max-si 0 # return
PE1 configuration file
# sysname PE1 # multicast ipv6 mvpn ipv6-underlay 2001:DB8:115::1 # ip vpn-instance VPNA ipv6-family route-distinguisher 100:1 vpn frr apply-label per-instance vpn-target 111:1 export-extcommunity evpn vpn-target 111:1 import-extcommunity evpn multicast ipv6 routing-enable mvpn vpn-target 111:1 export-extcommunity vpn-target 111:1 import-extcommunity ipv6 underlay enable c-multicast signaling bgp c-multicast frr c-multicast frr flow-detection-based 2111 multicast wtr 100 # acl ipv6 number 2111 rule 5 permit # segment-routing ipv6 locator PE1 ipv6-prefix 2001:DB8:15:: 64 static 32 # isis 1 is-level level-2 cost-style wide network-entity 10.0000.0000.0005.00 bier enable # ipv6 enable topology ipv6 segment-routing ipv6 locator PE1 auto-sid-disable # # interface GigabitEthernet0/1/0 undo shutdown ipv6 enable ipv6 address 2001:DB8:5::2/112 isis ipv6 enable 1 # interface GigabitEthernet0/1/1 undo shutdown ip binding vpn-instance VPNA ipv6 enable ipv6 address 2001:DB8:7::1/112 pim sm # interface GigabitEthernet0/1/2 undo shutdown ip binding vpn-instance VPNA ipv6 enable ipv6 address 2001:DB8:6::2/112 pim sm # interface LoopBack1 ipv6 enable ipv6 address 2001:DB8:115::1/128 isis ipv6 enable 1 # bgp 100 router-id 1.1.1.5 peer 2001:DB8:111::1 as-number 100 peer 2001:DB8:111::1 connect-interface LoopBack1 peer 2001:DB8:112::1 as-number 100 peer 2001:DB8:112::1 connect-interface LoopBack1 # ipv4-family unicast undo synchronization # ipv6-family mvpn policy vpn-target peer 2001:DB8:111::1 enable peer 2001:DB8:112::1 enable # ipv6-family vpnv6 policy vpn-target peer 2001:DB8:111::1 enable peer 2001:DB8:111::1 prefix-sid peer 2001:DB8:112::1 enable peer 2001:DB8:112::1 prefix-sid # ipv6-family vpn-instance VPNA import-route direct advertise l2vpn evpn segment-routing ipv6 locator PE1 evpn segment-routing ipv6 best-effort evpn peer 2001:DB8:7::2 as-number 65411 # l2vpn-family evpn policy vpn-target peer 2001:DB8:111::1 enable peer 2001:DB8:111::1 advertise encap-type srv6 peer 2001:DB8:112::1 enable peer 2001:DB8:112::1 advertise encap-type srv6 # bier sub-domain 0 ipv6 bfr-id 1 bfr-prefix interface LoopBack1 protocol isis end-bier locator PE1 sid 2001:DB8:15::1 encapsulation-type ipv6 bsl 256 max-si 0 # return