Example for Configuring Dual-ended Frame Loss Measurement (When an L2VPN Is Connected to an L3VPN)

This section provides an example for configuring dual-ended frame loss measurement when an L2VPN is connected to an L3VPN.

Networking Requirements

As networks continue to develop and diversify, various value-added services such as IPTV, video conferencing, and VoIP are becoming increasingly popular. The performance monitoring function can be used to check the performance of links that transmit services.

In Figure 1, CFM is configured to monitor the link between CE1 and PE3. CCMs are not expected to monitor link connectivity because the CCMs consume a lot of bandwidth resources. To meet higher requirements for voice services, a carrier needs a function to monitor frame loss performance on mobile links in real time and make prompt responses to calling performance deterioration.

A VLAN dot1q sub-interface, dot1q termination sub-interface, QinQ termination sub-interface, or L3VE interface on an L2VPN can be connected to an L3VPN. In this example, a VLAN dot1q sub-interface is used. An L2VPN is configured to access a public network, or L3VPN services are configured.

Figure 1 L2VPN connected to an L3VPN

Sub-interfaces3.1 in this example is GE0/1/17.1.

Configuration Roadmap

The configuration roadmap is as follows:

Configure on-demand dual-ended frame loss measurement.

Data Preparation

To complete the configuration, you need the following data:

MD name and MA name on CE1 and PE3
Interval at which LMMs are sent and number of intervals

Procedure

Configure basic Ethernet CFM functions, including outward-facing MEPs.

Configure basic Ethernet CFM functions on CE1 and PE3. Configure Ethernet CFM in compliance with IEEE Std 802.1ag-2007 and create an MD named md3 and an MA named ma3.

# Configure CE1.

<HUAWEI> system-view
[~HUAWEI] sysname CE1
[*HUAWEI] commit
[~CE1] interface gigabitethernet0/1/17.1
[*CE1-GigabitEthernet0/1/17.1] vlan-type dot1q 200
[*CE1-GigabitEthernet0/1/17.1] commit
[*CE1-GigabitEthernet0/1/17.1] quit
[~CE1] cfm enable
[*CE1] cfm md md3
[*CE1-md-md3] ma ma3
[*CE1-md-md3-ma-ma3] mep mep-id 3 interface gigabitethernet0/1/17.1 vlan 200 outward 
[*CE1-md-md3-ma-ma3] mep ccm-send mep-id 3 enable
[*CE1-md-md3-ma-ma3] remote-mep mep-id 4
[*CE1-md-md3-ma-ma3] remote-mep ccm-receive mep-id 4 enable
[*CE1-md-md3-ma-ma3] test-id 1 mep 3 remote-mep 4
[*CE1-md-md3-ma-ma3] commit

# Configure PE3.

<HUAWEI> system-view
[~HUAWEI] sysname PE3
[*HUAWEI] commit
[*PE3-GigabitEthernet0/1/17.1] vlan-type dot1q 200
[*PE3-GigabitEthernet0/1/17.1] commit
[*PE3-GigabitEthernet0/1/17.1] quit
[*PE3] commit
[*PE3] cfm enable
[*PE3] cfm commit
[*PE3] cfm md md3
[*PE3-md-md3] ma ma3
[*PE3-md-md3-ma-ma3] mep mep-id 4 interface gigabitethernet0/1/17.1 vlan 200 outward 
[*PE3-md-md3-ma-ma3] mep ccm-send mep-id 4 enable
[*PE3-md-md3-ma-ma3] remote-mep mep-id 3
[*PE3-md-md3-ma-ma3] remote-mep ccm-receive mep-id 3 enable
[*PE3-md-md3-ma-ma3] test-id 1 mep 4
[*PE3-md-md3-ma-ma3] commit

Configure dual-ended frame loss measurement.

# Configure PE3.

[~PE3-md-md3-ma-ma3] loss-measure dual-ended continual test-id 1
[*PE3-md-md3-ma-ma3] quit
[*PE3-md-md3] quit
[*PE3] commit

# Configure CE1.

[~CE1-md-md3-ma-ma3] loss-measure dual-ended continual test-id 1
[*CE1-md-md3-ma-ma3] quit
[*CE1-md-md3] quit

Verify the configuration.

After completing the configuration, run the display y1731 statistic-type command to dual-ended frame loss statistics on CE1.

<CE1> display y1731 statistic-type dual-loss
Latest dual-ended loss statistics of test-id 1:
--------------------------------------------------------------------------------
Index    Local-loss    Local-loss ratio    Remote-loss    Remote-loss ratio
--------------------------------------------------------------------------------
    1             0             0.0000%              0              0.0000%
    2             0             0.0000%              0              0.0000%
    3             0             0.0000%              0              0.0000%
    4             0             0.0000%              0              0.0000%
    5             0             0.0000%              0              0.0000%
    6             0             0.0000%              0              0.0000%
    7             0             0.0000%              0              0.0000%
    8             0             0.0000%              0              0.0000%
    9             0             0.0000%              0              0.0000%
   10             0             0.0000%              0              0.0000%
--------------------------------------------------------------------------------
Average Local-loss  :          0    Average Local-loss Ratio  :   0.0000%
Maximum Local-loss  :          0    Maximum Local-loss Ratio  :   0.0000%
Minimum Local-loss  :          0    Minimum Local-loss Ratio  :   0.0000%
Average Remote-loss :          0    Average Remote-loss Ratio :   0.0000%
Maximum Remote-loss :          0    Maximum Remote-loss Ratio :   0.0000%
Minimum Remote-loss :          0    Minimum Remote-loss Ratio :   0.0000%

Configuration Files

CE1 configuration file

#

 sysname CE1
#
 interface GigabitEthernet0/1/17.1
 vlan-type dot1q 200
#
 cfm version standard
 cfm enable
#
 cfm md md3
  ma ma3
   mep mep-id 3 interface GigabitEthernet0/1/17.1 vlan 200 outward
   mep ccm-send mep-id 3 enable
   remote-mep mep-id 4
   remote-mep ccm-receive mep-id 4 enable
   test-id 1 mep 3 remote-mep 4
   loss-measure dual-ended continual test-id 1
#
return

PE3 configuration file

#

 sysname PE3
#
 interface GigabitEthernet0/1/17.1
 vlan-type dot1q 200
#
 cfm version standard
 cfm enable
#
 cfm md md3
  ma ma3
   mep mep-id 4 interface GigabitEthernet0/1/17.1 vlan 200 outward
   mep ccm-send mep-id 4 enable
   remote-mep mep-id 3
   remote-mep ccm-receive mep-id 3 enable
   test-id 1 mep 4
   loss-measure dual-ended continual test-id 1
#
return