display ap-system-profile

Function

The display ap-system-profile command displays reference and configuration information about an AP system profile.

Format

display ap-system-profile { all | name profile-name }

Parameters

Parameter	Description	Value
all	Displays information about all AP system profiles.	-
name profile-name	Displays information about a specified AP system profile.	The AP system profile must exist.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run the display ap-system-profile command to view configuration and reference information about an AP system profile.

Example

# Display information about all AP system profiles.

<HUAWEI> display ap-system-profile all
----------------------------------------------------------
Profile name                   Reference
----------------------------------------------------------
default                        1
ap-system1                     0
----------------------------------------------------------
Total: 2

**Table 1** Description of the **display ap-system-profile all** command output
Item	Description
Profile name	Name of an AP system profile.
Reference	Number of times an AP system profile is referenced.

# Display information about the AP system profile ap-system1.

<HUAWEI> display ap-system-profile name ap-system1
------------------------------------------------------------------------------  
AC priority                                    : -
Protect AC IP address                          : -
Primary AC                                     : -
Backup AC                                      : -
AP management VLAN                             : -
Keep service                                   : disable
Keep service allow new access                  : disable
Keep service allow new access no auth          : disable
Temporary management switch                    : disable
Temporary management psk                       : ******
Card connect type                              : serial
Mesh role                                      : mesh-node
STA access mode                                : disable
STA whitelist profile                          : -
STA blacklist profile                          : -
EAPOL start mode                               : multicast
EAPOL start transform                          : equal-bssid
EAPOL response mode                            : unicast learning
EAPOL response transform                       : equal-bssid
AP LLDP message transmission delay time(s)     : 2
AP LLDP message transmission hold multiplier   : 4
AP LLDP message transmission interval time(s)  : 30
AP LLDP restart delay time(s)                  : 2
AP LLDP admin status                           : txrx
AP LLDP report interval time(s)                : 30
AP LLDP report enable                          : disable
AP device high temperature threshold (degree C): -
AP environment high temperature threshold (degree C) : -
AP CPU high temperature threshold (degree C)   : -
AP NP high temperature threshold (degree C)    : -
AP device low temperature threshold (degree C) : -
AP environment low temperature threshold (degree C)  : -
AP CPU low temperature threshold (degree C)    : -
AP NP low temperature threshold (degree C)     : -
AP CPU usage threshold(%)                      : 90
AP memory usage threshold(%)                   : 80
AP disk usage threshold(%)                     : 95
Alarm restriction                              : enable
Alarm restriction period(s)                    : 60
Log server IP address                          : -
Log server Port                                : - 
Log record level                               : info
Ethernet port MTU(byte)                        : 1500
Telnet                                         : disable
STelnet server                                 : enable 
SFTP server                                    : enable
Console                                        : enable
STA ARP-ND Proxy before-assoc                  : disable 
Antenna output mode                            : split
Led                                            : on
Led off time range                             : -
DHCP client option12                           : ap-name
Console ble-mode                               : dynamic
Report disassoc request                        : enable
Sample time(s)                                 : 30
Dynamic blacklist aging time(s)                : 600
MPP active reselection                         : disable
AP report to                                   : server
Server IP                                      : 0.0.0.0
Server port                                    : -
AC port                                        : -
Device aging-time(minute)                      : 3
PoE max power(mW)                              : 380000
PoE power reserved(%)                          : -
PoE power threshold(%)                         : -
PoE af inrush                                  : disable
PoE high inrush                                : disable
USB                                            : disable
SSH config                                                                      
  Client first time                            : disable                        
  User interface vty 0                                                          
    Idle timeout                               : 5min 0s                        
    Screen length                              : 24                             
    ACL inbound                                : -                              
    ACL outbound                               : -                              
    ACL ipv6 inbound                           : -                              
    ACL ipv6 outbound                          : -   
  User interface vty 1                                                          
    Idle timeout                               : 5min 0s                        
    Screen length                              : 24                             
    ACL inbound                                : -                              
    ACL outbound                               : -                              
    ACL ipv6 inbound                           : -                              
    ACL ipv6 outbound                          : -   
  User interface vty 2                                                          
    Idle timeout                               : 5min 0s                        
    Screen length                              : 24                             
    ACL inbound                                : -                              
    ACL outbound                               : -                              
    ACL ipv6 inbound                           : -                              
    ACL ipv6 outbound                          : -   
  User interface vty 3                                                          
    Idle timeout                               : 5min 0s                        
    Screen length                              : 24                             
    ACL inbound                                : -                              
    ACL outbound                               : -                              
    ACL ipv6 inbound                           : -                              
    ACL ipv6 outbound                          : -   
  User interface vty 4                                                          
    Idle timeout                               : 5min 0s                        
    Screen length                              : 24   
    ACL inbound                                : -                              
    ACL outbound                               : -                              
    ACL ipv6 inbound                           : -                              
    ACL ipv6 outbound                          : -   
AC protect link switch mode                    : priority
AC protect link switch packet loss echo probe time           : 20
AC protect link switch packet loss start threshold(%)        : 20
AC protect link switch packet loss gap threshold(%)          : 15
Traffic optimize broadcast suppression ARP     : enable
Traffic optimize broadcast suppression IGMP    : enable
Traffic optimize broadcast suppression ND      : enable
Traffic optimize broadcast suppression DHCP    : enable                          
Traffic optimize broadcast suppression DHCPv6  : enable                          
Traffic optimize broadcast suppression MDNS    : enable                          
Traffic optimize broadcast suppression other broadcast       : enable            
Traffic optimize broadcast suppression other multicast       : enable 
Traffic optimize broadcast suppression ARP rate limit(pps)   : 256
Traffic optimize broadcast suppression IGMP rate limit(pps)  : 256
Traffic optimize broadcast suppression ND rate limit(pps)    : 256
Traffic optimize broadcast suppression DHCP rate limit(pps)  : 256               
Traffic optimize broadcast suppression DHCPv6 rate limit(pps): 256               
Traffic optimize broadcast suppression MDNS rate limit(pps)  : 256               
Traffic optimize broadcast suppression other broadcast rate limit(pps) : 256     
Traffic optimize broadcast suppression other multicast rate limit(pps) : 256  
Wmi server profile  
  Index 1                                       : 1  
  Index 2                                       : 2 
Broadcast suppression auto-detect packets(pps)  : 256                            
Multicast suppression auto-detect packets(pps)  : 256                            
Unicast suppression auto-detect packets(pps)    : 128  
Station connectivity-detect switch              : enable
NP fast-forwarding switch                       : enable
NP CAPWAP reassembly switch                     : enable
------------------------------------------------------------------------------

**Table 2** Description of the **display ap-system-profile name** *profile-name* command output
Item	Description
AC priority	AC priority. To configure this parameter, run the priority command.
Protect AC IP address	IP address of the standby AC. To configure this parameter, run the protect-ac command.
Primary AC	IP address of the primary AC. To configure this parameter, run the primary-access command.
Backup AC	IP address of the backup AC. To configure this parameter, run the backup-access command.
AP management VLAN	Management VLAN of an AP. To configure this parameter, run the management-vlan command.
Keep service	Whether service endurance upon CAPWAP link disconnection between the AP and AC is enabled. enable: This function is enabled. disable: This function is disabled. To configure this parameter, run the keep-service enable command.
Keep service allow new access	Whether new STAs in open system, WEP, or WPA/WPA2-PSK authentication mode are allowed to go online when an AP is offline. enable: This function is enabled. disable: This function is disabled. To configure this parameter, run the keep-service enable allow new-access command.
Keep service allow new access no auth	Whether the offline AP allows access of new STAs using Portal or MAC address authentication. enable: This function is enabled. disable: This function is disabled. To configure this parameter, run the keep-service enable allow new-access no-auth command.
Temporary management switch	Status of the offline management and antenna alignment VAPs. enable: This function is enabled. disable: This function is disabled. To configure this parameter, run the temporary-management disable (AP system profile view) command.
Card connect type	Communication connection type between IoT cards and APs. To configure this parameter, run the card connect-type command.
Temporary management psk	Key for the offline management and antenna alignment VAPs. To configure this parameter, run the temporary-management psk command.
Mesh role	Mesh role. To configure this parameter, run the mesh-role command.
STA access mode	STA access mode. To configure this parameter, run the sta-access-mode command.
STA whitelist profile	Name of a STA whitelist profile referenced by an AP system profile. To configure this parameter, run the sta-access-mode command.
STA blacklist profile	Name of a STA blacklist profile referenced by an AP system profile. To configure this parameter, run the sta-access-mode command.
EAPOL start mode	EAPOL-start packet encapsulation mode. To configure this parameter, run the eapol-start dest-address transform-to command.
EAPOL start transform	EAPOL-start packet conversion mode. To configure this parameter, run the eapol-start dest-address transform-condition command.
EAPOL response mode	EAPOL-response packet encapsulation mode. To configure this parameter, run the eapol-response dest-address transform-to command.
EAPOL response transform	EAPOL-response packet conversion mode. To configure this parameter, run the eapol-response dest-address transform-condition command.
AP LLDP message transmission delay time(s)	Delay for an AP to send LLDP packets to neighbors. To configure this parameter, run the lldp message-transmission delay (AP system profile view) command.
AP LLDP message transmission hold multiplier	Hold time multiplier of AP information on neighbors. To configure this parameter, run the lldp message-transmission hold-multiplier (AP system profile view) command.
AP LLDP message transmission interval time(s)	Interval at which an AP sends LLDP packets to neighbors. To configure this parameter, run the lldp message-transmission interval (AP system profile view) command.
AP LLDP restart delay time(s)	Delay in re-enabling LLDP. To configure this parameter, run the lldp restart-delay command.
AP LLDP admin status	LLDP mode on an AP. tx: The AP sends but does not receive LLDP packets. rx: The AP receives but does not send LLDP packets. txrx: The AP sends and receives LLDP packets. To configure this parameter, run the lldp admin-status command.
AP LLDP report interval time(s)	Interval at which an AP reports LLDP neighbor information to an AC. To configure this parameter, run the lldp report-interval command.
AP LLDP report enable	Whether an AP is enabled to report information about its LLDP neighbors. To configure this parameter, run the lldp report enable command.
AP device high temperature threshold (degree C)	Upper device temperature alarm threshold of an AP. To configure this parameter, run the high-temperature threshold command.
AP environment high temperature threshold (degree C)	Upper ambient temperature alarm threshold of an AP. To configure this parameter, run the high-temperature threshold command.
AP CPU high temperature threshold (degree C)	Upper CPU temperature alarm threshold of an AP. To configure this parameter, run the high-temperature threshold command.
AP NP high temperature threshold (degree C)	Upper NP chip temperature alarm threshold of an AP. To configure this parameter, run the high-temperature threshold command.
AP device low temperature threshold (degree C)	Lower device temperature alarm threshold of an AP. To configure this parameter, run the low-temperature threshold command.
AP environment low temperature threshold (degree C)	Lower ambient temperature alarm threshold of an AP. To configure this parameter, run the low-temperature threshold command.
AP CPU low temperature threshold (degree C)	Lower CPU temperature alarm threshold of an AP. To configure this parameter, run the low-temperature threshold command.
AP NP low temperature threshold (degree C)	Lower NP chip temperature alarm threshold of an AP. To configure this parameter, run the low-temperature threshold command.
AP CPU usage threshold(%)	CPU usage alarm threshold of an AP. To configure this parameter, run the cpu-usage threshold command.
AP memory usage threshold(%)	Memory usage alarm threshold of an AP. To configure this parameter, run the memory-usage threshold command.
AP disk usage threshold(%)	Disk usage alarm threshold of an AP. To configure this parameter, run the disk-usage threshold command.
Alarm restriction	Alarm suppression status of an AP. To configure this parameter, run the alarm-restriction disable command.
Alarm restriction period(s)	Alarm suppression period of an AP. To configure this parameter, run the alarm-restriction period command.
Log server IP address	IP address of the log server. To configure this parameter, run the log-server command.
Log server Port	Port number of the log server. To configure this parameter, run the log-server command.
Log record level	Level of AP logs to be backed up. To configure this parameter, run the log-record-level command.
Ethernet port MTU(byte)	MTU of Ethernet interfaces. To configure this parameter, run the mtu command.
Telnet	Whether AP Telnet login is enabled. To configure this parameter, run the telnet enable command.
STelnet server	STelnet server status of an AP. To configure this parameter, run the stelnet server disable command.
SFTP server	SFTP server status of an AP. To configure this parameter, run the sftp server disable command.
Console	Whether AP console port login is enabled. To configure this parameter, run the console disable command.
STA ARP-ND Proxy before-assoc	Whether an AP is enabled to send ARP/ND proxy packets for a STA before the STA is successfully associated. To configure this parameter, run the sta arp-nd-proxy before-assoc command.
Antenna output mode	Output mode of the AP's 2.4 GHz or 5 GHz antenna. To configure this parameter, run the antenna-output command.
Led	Whether AP indicators are allowed to turn on. on: The AP indicators are allowed to turn on. off: The AP indicators are forbidden to turn on. To configure this parameter, run the led off command.
Led off time range	Time range within which the AP indicators are forbidden to turn on. To configure this parameter, run the led off command.
DHCP client option12	AP information contained in Option 12 carried in DHCP messages reported by an AP. ap-name: AP name contained in Option 12 carried in DHCP messages reported by an AP. ap-type ap-mac: AP type and MAC address contained in Option 12 carried in DHCP messages reported by an AP. disable: The Option 12 is not carried in DHCP messages reported by an AP. To configure this parameter, run the dhcp client option12 command.
Console ble-mode	Bluetooth-based serial port login mode. dynamic persistent disable: The Bluetooth-based serial port login function is disabled. To configure this parameter, run the console ble-mode (AP system profile view) command.
Report disassoc request	Whether an AP is enabled to report disassociation request packets of STAs to the AC. To configure this parameter, run the report-disassoc-request disable command.
Sample time(s)	AP's sampling interval. To configure this parameter, run the sample-time command.
Dynamic blacklist aging time(s)	Aging time of a dynamic blacklist entry. To configure this parameter, run the dynamic-blacklist aging-time command.
MPP active reselection	Active MPP reselection. To configure this parameter, run the mpp-active-reselection enable command.
AP report to	Mode in which an AP reports spectrum data. server: The AP reports spectrum data to a spectrum server directly. AC: The AP reports spectrum data to a spectrum server via the AC. To configure this parameter, run the spectrum-analysis server command.
Server IP	IP address of the spectrum server. To configure this parameter, run the spectrum-analysis server command.
Server port	Port number (UDP port number) of the spectrum server. To configure this parameter, run the spectrum-analysis server command.
AC port	Port number used by the AC to receive spectrum data (in UDP packets) from the AP. To configure this parameter, run the spectrum-analysis server command.
Device aging-time(minute)	Aging time of non-Wi-Fi device data on an AC. To set the aging time, run the spectrum-analysis non-wifi-device aging-time command.
PoE max power(mW)	Maximum output power of the central AP. To configure this parameter, run the poe max-power (AP system profile view) command.
PoE power reserved(%)	Percentage of reserved PoE power to the available PoE power on the central AP. To configure this parameter, run the poe power-reserved (AP system profile view) command.
PoE power threshold(%)	Alarm threshold of PoE power consumption percentage on the central AP. To configure this parameter, run the poe power-threshold (AP system profile view) command.
PoE af inrush	PoE standard of the central AP. To configure this parameter, run the poe af-inrush enable (AP system profile view) command.
PoE high inrush	Whether the central AP is enabled to allow high inrush current during power-on. To configure this parameter, run the poe high-inrush enable (AP system profile view) command.
Group address start	Start multicast group address. To configure this parameter, run the igmp-snooping group-bandwidth (AP system profile view) command.
Group address end	End multicast group address. To configure this parameter, run the igmp-snooping group-bandwidth (AP system profile view) command.
Bandwidth(kbps)	Bandwidth of global multicast groups on an AP. To configure this parameter, run the igmp-snooping group-bandwidth (AP system profile view) command.
USB	USB status. To configure this parameter, run the usb enable (AP system profile view) command.
SSH config	SSH configurations.
Client first time	Whether initial authentication is enabled on the SSH client. To configure this parameter, run the ssh client first-time enable (AP system profile view) command.
User interface vty X	VTY user interface X. The value of X ranges from 0 to 4.
Idle timeout	Timeout period of user connections. To configure this parameter, run the user-interface vty idle-timeout command.
Screen length	Number of lines on each terminal screen. To configure this parameter, run the user-interface vty screen-length command.
ACL inbound	ACL that restricts STAs with a specified IPv4 address or within a specified IP address segment from logging in to the device. To configure this parameter, run the user-interface vty acl command.
ACL outbound	ACL that restricts IPv4 STAs who have logged in to the device from logging in to other devices. To configure this parameter, run the user-interface vty acl command.
ACL ipv6 inbound	ACL that restricts STAs with a specified IPv6 address or within a specified IP address segment from logging in to the device. To configure this parameter, run the user-interface vty acl command.
ACL ipv6 outbound	ACL that restricts IPv6 STAs who have logged in to the device from logging in to other devices. To configure this parameter, run the user-interface vty acl command.
AC protect link switch mode	Active/standby link switchover mode. To configure this parameter, run the ac protect link-switch mode command.
AC protect link switch packet loss echo probe time	Number of Echo probe packets sent within a statistics collection interval. To configure this parameter, run the ac protect link-switch packet-loss echo-probe-time command.
AC protect link switch packet loss start threshold(%)	Packet loss rate start threshold for an active/standby link switchover. To configure this parameter, run the ac protect link-switch packet-loss command.
AC protect link switch packet loss gap threshold(%)	Packet loss rate difference threshold for an active/standby link switchover. To configure this parameter, run the ac protect link-switch packet-loss command.
Traffic optimize broadcast suppression ARP	Whether the suppression function is enabled for ARP packets. To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.
Traffic optimize broadcast suppression IGMP	Whether the suppression function is enabled for IGMP packets. To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.
Traffic optimize broadcast suppression ND	Whether the suppression function is enabled for ND packets. To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.
Traffic optimize broadcast suppression DHCP	Whether the suppression function is enabled for DHCP packets. To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.
Traffic optimize broadcast suppression DHCPv6	Whether the suppression function is enabled for DHCPv6 packets. To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.
Traffic optimize broadcast suppression MDNS	Whether the suppression function is enabled for mDNS packets. To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.
Traffic optimize broadcast suppression other broadcast	Whether the suppression function is enabled for broadcast packets other than ARP, DHCP, DHCPv6, and ND packets. To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.
Traffic optimize broadcast suppression other multicast	Whether the suppression function is enabled for multicast packets other than IGMP and mDNS packets. To configure this parameter, run the traffic-optimize broadcast-suppression disable (AP system profile view) command.
Traffic optimize broadcast suppression ARP rate limit(pps)	Rate threshold for ARP packets. To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.
Traffic optimize broadcast suppression IGMP rate limit(pps)	Rate threshold for IGMP packets. To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.
Traffic optimize broadcast suppression ND rate limit(pps)	Rate threshold for ND packets. To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.
Traffic optimize broadcast suppression DHCP rate limit(pps)	Rate threshold for DHCP packets. To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.
Traffic optimize broadcast suppression DHCPv6 rate limit(pps)	Rate threshold for DHCPv6 packets. To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.
Traffic optimize broadcast suppression MDNS rate limit(pps)	Rate threshold for mDNS packets. To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.
Traffic optimize broadcast suppression other broadcast rate limit(pps)	Rate threshold for broadcast packets other than ARP, DHCP, DHCPv6, and ND packets. To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.
Traffic optimize broadcast suppression other multicast rate limit(pps)	Rate threshold for multicast packets other than IGMP and mDNS packets. To configure this parameter, run the traffic-optimize broadcast-suppression rate-threshold (AP system profile view) command.
Wmi server profile	WMI profile bound to the AP system profile. Index 1: WMI profile with index 1 Index 2: WMI profile with index 2 To configure this parameter, run the wmi-server (AP system profile view) command.
Broadcast suppression auto-detect packets(pps)	Rate threshold of broadcast packets. To configure this parameter, run the broadcast-suppression auto-detect (AP system profile view) command.
Multicast suppression auto-detect packets(pps)	Rate threshold of multicast packets. To configure this parameter, run the multicast-suppression auto-detect (AP system profile view) command.
Unicast suppression auto-detect packets(pps)	Rate threshold of unknown unicast packets. To configure this parameter, run the unicast-suppression auto-detect (AP system profile view) command.
Station connectivity-detect switch	Whether terminal connectivity check is enabled. To configure this parameter, run the station connectivity-detect disable command.
NP fast-forwarding switch	Whether the NP fast forwarding function is enabled. To configure this parameter, run the np fast-forwarding disable (AP system profile view) command.
NP CAPWAP reassembly switch	Whether the NPCAPWAP reassembly function is enabled. To configure this parameter, run the np capwap-reassembly disable (AP system profile view) command.