DEVM_1.3.6.1.4.1.2011.5.25.219.2.2.5 hwBoardInvalid-132619

Trap Buffer Description

The board totally failed. (EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalIndex=[EntPhysicalIndex], EntPhysicalName=[EntPhysicalName], EntityType=[EntityType], EntityTrapFaultID=132619, Reason=The master or slave ACT signal of the MPU board is abnormal.)

The overall function of the board does not take effect.

In VS mode, this trap is supported only by the admin VS.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Alert
Mnemonic Code	hwBoardInvalid
Trap OID	1.3.6.1.4.1.2011.5.25.219.2.2.5
MIB	HUAWEI-ENTITY-TRAP-MIB
Alarm ID	0x0813002e
Alarm Name	hwBoardInvalid
Alarm Type	equipmentAlarm
Raise or Clear	Raise
Match trap	DEVM_1.3.6.1.4.1.2011.5.25.219.2.2.6 hwBoardInvalidResume-132619

Trap Buffer Parameters

Parameter	Description
EntityPhysicalIndex	Indicates the index of the physical entity.
EntPhysicalIndex	Indicates the index of the physical entity.
EntityTrapFaultID	Indicates the error code.
EntPhysicalName	Indicates the name of the entity such as a chassis.
EntityType	Indicates the type of the physical entity. The value can be one of the following: 1: mpu(1) 2: lpu(2) 3: sfu(3) 4: pic(4) 5: cfcard(5) 6: ofc(6) 7: npu(7)
Reason	Indicates the description of the cause of the trap.

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.219.1.1	hwEntityPhysicalIndex	-
1.3.6.1.2.1.47.1.1.1.1.7	entPhysicalName	entPhysicalIndex
1.3.6.1.4.1.2011.5.25.219.1.2	hwEntityTrapEntType	-
1.3.6.1.4.1.2011.5.25.219.1.3	hwEntityTrapFaultID	-
1.3.6.1.4.1.2011.5.25.219.1.13	hwEntityTrapReasonDescr	-
1.3.6.1.4.1.2011.5.25.31.1.1.1.1.2	hwEntityOperStatus	entPhysicalIndex

Impact on the System

Services on the board may be affected and even interrupted. A speedy solution is required.

Possible Causes

The master or slave ACT signal of the MPU board is abnormal.

Procedure

1. Check whether other boards have low-power-related alarms or power-related alarms. If so, handle these alarms first.

2. Remove and reinstall the current standby main control board and check whether the standby main control board is securely installed, whether any bent pins exist, and whether the connectors of the standby main control board are normal. Then, go to Step 4.

3. If the device is reset, remove the other main control board and check whether the main control board is securely installed, whether any bent pins exist, and whether the connectors of the main control board are normal. Then, go to Step 4.

4. If the board is not securely installed, install it securely.

5. If the backplane has bent pins, avoid installing a new board into the faulty slot. Contact technical support.

6. If only the connectors of the board are found to be faulty, replace the board and go to Step 8.

7. If the standby main control board is still not registered or the alarm persists, contact technical support.

8. End.