DEVM_1.3.6.1.4.1.2011.5.25.129.2.1.9 hwEntityInvalid-67638

Trap Buffer Description

Physical entity failed. (BaseTrapSeverity=[BaseTrapSeverity], BaseTrapProbableCause=[67638], BaseTrapEventType=[BaseTrapEventType], EntityPhysicalIndex=[EntityPhysicalIndex], EntPhysicalContainedIn=[EntContainedIn], EntPhysicalName=[EntPhysicalName], RelativeResource=[RelativeResource], ReasonDescription=The power module was properly installed but was not powered on.)

Physical entity failed.

In VS mode, this trap is supported only by the admin VS.

Trap Attributes

Trap Attribute	Description
Alarm or Event	Alarm
Trap Severity	Alert
Mnemonic Code	hwEntityInvalid
Trap OID	1.3.6.1.4.1.2011.5.25.129.2.1.9
MIB	HUAWEI-BASE-TRAP-MIB
Alarm ID	0x08130055
Alarm Name	hwEntityInvalid
Alarm Type	equipmentAlarm
Raise or Clear	Raise
Match trap	DEVM_1.3.6.1.4.1.2011.5.25.129.2.1.10 hwEntityResume-67638

Trap Buffer Parameters

Parameter	Description
BaseTrapSeverity	To describe the level of trap.
ProbableCause	To describe the probable cause of trap.
BaseTrapEventType	To describe the type of trap.
EntityPhysicalIndex	The index of the physical entity.
EntContainedIn	The value of entPhysicalIndex for the physical entity.
EntPhysicalName	The textual name of the physical entity.
RelativeResource	This object may contain a key word to indicate the relative resource of an entity.
ReasonDescription	To describe the reason of trap in DisplayString style.

VB Parameters

VB OID	VB Name	VB Index
1.3.6.1.4.1.2011.5.25.129.1.1	hwBaseTrapSeverity	-
1.3.6.1.4.1.2011.5.25.129.1.2	hwBaseTrapProbableCause	-
1.3.6.1.4.1.2011.5.25.129.1.3	hwBaseTrapEventType	-
1.3.6.1.2.1.47.1.1.1.1.4	entPhysicalContainedIn	entPhysicalIndex
1.3.6.1.2.1.47.1.1.1.1.7	entPhysicalName	entPhysicalIndex
1.3.6.1.4.1.2011.5.25.129.1.4	hwBaseTrapRelativeResource	-
1.3.6.1.4.1.2011.5.25.129.1.5	hwBaseTrapReasonDescr	-

Impact on the System

A power failure may lead to power supply insufficiency, causing the board to reset. This indirectly affects services, and therefore this problem needs to be solved.

Possible Causes

The power module was properly installed but was not powered on.

Procedure

1. Check whether the power supply module is stably installed.

If so, go to Step 2.
If not, go to Step 6.

2. Check whether the power supply module is powered on. If the power supply module is not powered on, power on it. Then, check whether the alarm is cleared.

If so, go to Step 6.
If not, go to Step 4.

3. Perform an active/standby switchover. Then, check whether the alarm is cleared.

If so, go to Step 6.
If not, go to Step 4.

4. Replace the power supply module. Power off the faulty power module before replacing it. Then, check whether the alarm is cleared.

If so, go to Step 6.
If not, go to Step 5.

5. Collect trap, log, and configuration information, and contact technical support.

6. End.