display interface phy-option
Function
The display interface phy-option command can view the physical features of a specified interface.
Example
The actual command output varies according to the device. The command output here is only an example.
<HUAWEI> display interface phy-option gigabitethernet 0/1/0 GigabitEthernet0/1/0 Port Physical Status : DOWN Physical Down Reason : transceiver offline Loopback : none Duplex mode : full-duplex negotiation : disable Pause Flowcontrol : Receive Enable and Send Disable SFP information: Optical transceiver is offline! Carrier delay(up-hold-time) is 200 msec, Carrier delay(down-hold-time) is 0 msec
<HUAWEI> display interface phy-option FlexE 0/1/129 FlexE0/1/129 Port Physical Status : UP Physical Down Reason : none Duplex mode : full-duplex Loopback : none Pause Flowcontrol : Receive Enable and Send Enable Optical information: Factor/Module: QSFP28, Standard: Reserved The Vendor PN is OM9380L The Vendor Name is HISILICON Transceiver max BW: 53.25G, Transceiver Mode: SingleMode Connector Type: LC, Transmission Distance: 10km WaveLength: 1311nm Rx Power: 2.35dBm, Tx Power: 2.96dBm Rx Warning range: [-8.900, 4.199]dBm, Tx Warning range: [-4.000, 4.199]dBm Carrier delay(up-hold-time) is 200 msec, Carrier delay(down-hold-time) is 0 msec FEC information: FEC pre-alarm trigger threshold : 1.00E-5 FEC pre-alarm recover threshold : 1.00E-6
<HUAWEI> display interface phy-option GigabitEthernet0/1/0 GigabitEthernet0/1/0 Port Physical Status : DOWN Physical Down Reason : LOS Loopback : none Duplex mode : full-duplex negotiation : disable Pause Flowcontrol: Receive : Enable Send : Disable Optical information: The Vendor PN is MXPD-243SI The Vendor Name is HG GENUINE The Vendor Private Information is NA, Transceiver Identifier: ESFP Port BW: 1G, Transceiver max BW: 1G, Transceiver Mode: SingleMode WaveLength: 1310.00nm, Transmission Distance: 10km Rx Power: -39.28dBm, Working range: [-19.000, -2.999]dBm Tx Power: -6.01dBm, Working range: [-8.043, -4.042]dBm Carrier delay(up-hold-time) is 2000 msec, Carrier delay(down-hold-time) is 0 msec
<HUAWEI> display interface phy-option FlexE0/1/129 FlexE0/1/129 Pause Flowcontrol: Receive : Enable Send : Disable Carrier delay(up-hold-time) is 2000 msec, Carrier delay(down-hold-time) is 0 msec
| Item | Description |
|---|---|
| Port Physical Status | Physical link status of an interface.
|
| Physical layer | Physical link. |
| Physical Down Reason | Indicates the reason why the physical link of the interface goes Down. |
| Scramble | Scrambling function is enabled. |
| Clock | Clock mode. |
| CRC | Number packets that fail the CRC. |
| Loopback | Whether loopback is enabled. The options are as follows:
|
| Flag J0 | Value of the J0 overhead byte. |
| Flag J1 | Value of the J1 overhead byte. |
| Flag C2 | Value of the C2 overhead byte. |
| Optical information | Basic information about the optical module. |
| transceiver max bw | Maximum bandwidth of the optical module. |
| Transmission-alarm delay(holdup-timer) | Delay for clearing an alarm. If alarm clearance messages are received within a filtering interval set using the transmission-alarm holdup-timer command, the alarm clearance messages are filtered. An alarm is cleared only when an alarm clearance message is received after the filtering interval expires. |
| Transmission-alarm delay(holdoff-timer) | Delay for generating an alarm. If alarm generation messages are received within a filtering interval set using the transmission-alarm holdoff-timer command, the alarm generation messages are filtered. An alarm is generated only when an alarm generation message is received after the filtering interval expires. |
| FEC Mode | Forward error correction (FEC) mode:
|
| FEC information | FEC bit error ratio detection information. |
| OTU TTI | TTI of the received OUT. |
| ODU TTI | TTI of the received ODU. |
| Duplex mode | Duplex mode (full-duplex mode full-duplex; Half-duplex mode half-duplex).
|
| negotiation | Whether auto-negotiation is enabled. |
| Pause Flowcontrol | Whether Ethernet flow control frames are enabled.
|
| SFP information | Indicates the basic information about an optical module. |
| Carrier delay(up-hold-time) | Run the carrier up-hold-time command to set the delay time for the interface to go Up when the interface status changes from Down to Up. Otherwise, the default time is displayed. |
| Carrier delay(down-hold-time) | Run the carrier down-hold-time command to set the delay time for the interface to go Down when the interface status changes from Up to Down. Otherwise, the default time is displayed. |
| connector type | connector type. |
| wavelength | Wavelength. |
| rx power | Receive power. |
| receive | Receive. |
| factor/module | Module Type. |
| tx power | Transmit Power. |
| rx warning range | Alarm range of the receive power of the optical module. |
| port bw | Port Bandwidth. |
| send | Send. |