The l2-multicast static-group command configures a static member interface.
The undo l2-multicast static-group command cancels the configuration.
By default, a dynamic member interface is used.
l2-multicast static-group [ source-address source-address ] group-address group-address
l2-multicast static-group [ source-address source-address ] group-address group-address dot1q vid vid
l2-multicast static-group [ source-address source-address ] group-address group-address qinq pe-vid pe-vid ce-vid ce-id
undo l2-multicast static-group [ source-address source-address ] group-address { group-address | all }
undo l2-multicast static-group [ source-address source-address ] group-address { group-address | all } qinq pe-vid pe-vid ce-vid ce-id
undo l2-multicast static-group [ source-address source-address ] group-address { group-address | all } dot1q vid vid
| Parameter | Description | Value |
|---|---|---|
| source-address source-address |
Specifies a multicast source address. |
The value can be a Class A, Class B, or Class C address, in dotted decimal notation. |
| group-address group-address |
Specifies a multicast group address. |
The value ranges from 224.0.1.0 to 239.255.255.255, in dotted decimal notation. |
| dot1q vid vid |
Specifies a VLAN ID for a Dot1q termination sub-interface. |
The value is an integer ranging from 1 to 4094. |
| qinq pe-vid pe-vid |
Specifies an outer VLAN ID for a QinQ termination sub-interface. |
The value is an integer ranging from 1 to 4094. |
| ce-vid ce-id |
Specifies an inner VLAN ID for a QinQ termination sub-interface. |
The value is an integer ranging from 1 to 4094. |
| all |
Indicates all VLAN/sVSIs/BDs multicast groups. |
- |
Usage Scenario
If hosts connected to an interface need to regularly receive data for a multicast group or a source-specific multicast group, the l2-multicast static-group command can be used to configure the interface as a static member interface.
Static member interfaces can be configured on different positions on a network to enable users to receive data for specific multicast groups or source-specific multicast groups regularly. The commands listed in the following table can be run in any order. Run one or more commands as required to configure static member interfaces. For details, see Table 1.Prerequisites
IGMP snooping has been configured globally and in a VLAN/VSI/BD.
Configuration Impact
A static member interface does not respond to IGMP Query messages. After the undo l2-multicast static-group command is run on a static member interface, the interface does not initiate an IGMP Leave message.
If the l2-multicast static-group command is run more than once, all configurations take effect.Precautions
If the number of (S, G) entries relevant to a group has reached the maximum value (128), no static entry will be created after the l2-multicast static-group command is run. This means that no entry relevant to a static multicast group will be generated even after the reset igmp-snooping group all command is run in the system view to refresh entries.
<HUAWEI> system-view [~HUAWEI] igmp-snooping enable [*HUAWEI] mpls [*HUAWEI-mpls] quit [*HUAWEI] mpls l2vpn [*HUAWEI-l2vpn] quit [*HUAWEI] vsi vsi0 [*HUAWEI-vsi-vsi0] pwsignal ldp [*HUAWEI-vsi-vsi0-ldp] vsi-id 100 [*HUAWEI-vsi-vsi0-ldp] quit [*HUAWEI-vsi-vsi0] quit [*HUAWEI] interface GigabitEthernet 0/1/1.1 [*HUAWEI-GigabitEthernet0/1/1.1] vlan-type dot1q 10 [*HUAWEI-GigabitEthernet0/1/1.1] l2 binding vsi vsi0 [*HUAWEI-GigabitEthernet0/1/1.1] l2-multicast static-group source-address 10.1.1.1 group-address 225.1.1.2 vsi vsi0