ospfv3 suppress-flapping peer (interface view)

Function

The ospfv3 suppress-flapping peer command configures detection parameters for OSPFv3 neighbor relationship flapping suppression.

The undo ospfv3 suppress-flapping peer command restores the default detection parameters.

The ospfv3 suppress-flapping peer disable command disables OSPFv3 neighbor relationship flapping suppression from an interface.

The undo ospfv3 suppress-flapping peer disable command enables OSPFv3 neighbor relationship flapping suppression on an interface.

The ospfv3 suppress-flapping peer hold-down command configures the Hold-down mode and sets duration for this mode.

The undo ospfv3 suppress-flapping peer hold-down command cancels the Hold-down mode.

The ospfv3 suppress-flapping peer hold-max-cost disable command disables the Hold-max-cost mode.

The undo ospfv3 suppress-flapping peer hold-max-cost disable command enables the Hold-max-cost mode.

By default, the detection interval of OSPFv3 neighbor relationship flapping suppression is 60s, the suppression threshold is 10, and the interval for exiting from suppression is 120s.

By default, OSPFv3 neighbor relationship flapping suppression is enabled on all interfaces.

By default, the Hold-down mode is disabled, and the Hold-max-cost mode is enabled.

By default, the Hold-max-cost mode is enabled.

Format

ospfv3 suppress-flapping peer disable [ instance instance-id ]

ospfv3 suppress-flapping peer hold-down interval [ instance instance-id ]

ospfv3 suppress-flapping peer hold-max-cost disable [ instance instance-id ]

ospfv3 suppress-flapping peer { detecting-interval detecting-interval | threshold threshold | resume-interval resume-interval } ^* [ instance instance-id ]

undo ospfv3 suppress-flapping peer disable [ instance instance-id ]

undo ospfv3 suppress-flapping peer hold-down [ interval ] [ instance instance-id ]

undo ospfv3 suppress-flapping peer hold-max-cost disable [ instance instance-id ]

undo ospfv3 suppress-flapping peer { detecting-interval detecting-interval | threshold threshold | resume-interval resume-interval } ^* [ instance instance-id ]

Parameters

Parameter	Description	Value
instance instance-id	Specifies the ID of the instance to which an interface belongs.	The value is an integer ranging from 0 to 255.
hold-down interval	Specifies the duration of the Hold-down mode.	The value is an integer ranging from 1 to 86400, in seconds.
detecting-interval detecting-interval	Specifies the detection interval of OSPFv3 neighbor relationship flapping suppression. Each OSPF interface on which OSPFv3 neighbor relationship flapping suppression is enabled starts a flapping counter. If the interval between two successive neighbor status changes from Full to a non-Full state is shorter than detecting-interval, a valid flapping_event is recorded, and the flapping_count increases by 1.	The value is an integer ranging from 1 to 300, in seconds. The default value is 60s.
threshold threshold	Specifies the threshold of OSPF neighbor relationship flapping suppression. When the flapping_count reaches or exceeds threshold, flapping suppression takes effect.	The value is an integer ranging from 1 to 1000. The default value is 10.
resume-interval resume-interval	Specifies the interval for exiting from OSPFv3 neighbor relationship flapping suppression. If the interval between two successive neighbor status changes from Full to a non-Full state is longer than resume-interval, the flapping_count is reset. If OSPFv3 neighbor relationship flapping suppression works in hold-max-cost mode, resume-interval indicates the duration of this mode. The value of. resume-interval must be greater than that of. detecting-interval.	The value is an integer ranging from 2 to 1000, in seconds.

Task Name	Operations
ospf	write

Usage Guidelines

Usage Scenario

To configure detection parameters for OSPFv3 neighbor relationship flapping suppression on an interface, run the ospfv3 suppress-flapping peer command. However, keeping the default configurations is recommended.

By default, OSPFv3 neighbor relationship flapping suppression is enabled on all interfaces in the same OSPFv3 process. To disable the function from one of the interfaces, run the ospfv3 suppress-flapping peer disable command.

Flapping suppression works in either Hold-down or Hold-max-cost mode.

Hold-down mode: In the case of frequent flooding and topology changes during neighbor relationship establishment, interfaces prevent neighbor relationship reestablishment during Hold-down suppression, which minimizes LSDB synchronization attempts and packet exchanges.
Hold-max-cost mode: If the traffic forwarding path changes frequently, interfaces use 65535 as the cost of the flapping link during Hold-max-cost suppression, which prevents traffic from passing through the flapping link.
Flapping suppression can also work first in Hold-down mode and then in Hold-max-cost mode.
By default, the Hold-max-cost mode takes effect. To configure the Hold-down mode and set duration for this mode, run the ospfv3 suppress-flapping peer hold-down command.

Prerequisites

OSPFv3 neighbor relationship flapping suppression must have been enabled globally before you configure detection parameters for it. By default, the function is enabled. If it is disabled, run the undo suppress-flapping peer disable command to enable it before you configure the detection parameters.

OSPFv3 neighbor relationship flapping suppression must have been enabled globally before you enable the function on an interface using the undo ospfv3 suppress-flapping peer disable command. By default, the function is enabled globally. If it is disabled, run the undo suppress-flapping peer disable command to enable it first.

OSPFv3 neighbor relationship flapping suppression must have been enabled globally before you configure the Hold-down mode and set duration for this mode. By default, the function is enabled. If it is disabled, run the undo suppress-flapping peer disable command to enable it before you configure the Hold-down mode and set duration for this mode.

Precautions

The Hold-max-cost mode takes effect only unidirectionally. If a remote device does not support OSPFv3 neighbor relationship flapping suppression, bidirectional traffic between the local and remote devices may travel along different paths.

ospfv3 suppress-flapping peer (interface view)

Function

Format

Parameters

Views

Default Level

Task Name and Operations

Usage Guidelines

Example