loss-measure single-ended-synthetic local-ratio-threshold

Format

loss-measure single-ended-synthetic local-ratio-threshold test-id test-id-value upper-limit upper-limit lower-limit lower-limit

undo loss-measure single-ended-synthetic local-ratio-threshold test-id test-id-value [ upper-limit upper-limit lower-limit lower-limit ]

Parameters

Parameter	Description	Value
upper-limit upper-limit	Configures an upper alarm threshold for the near-end frame loss ratio of proactive LSM.	The value is a string of 1 to 8 case-insensitive characters, spaces not supported.
lower-limit lower-limit	Configures a lower alarm threshold for the near-end frame loss ratio of proactive SLM.	The value is a string of 1 to 8 case-insensitive characters, spaces not supported. The lower alarm threshold must be less than the upper alarm threshold.
test-id test-id-value	Specifies the ID of a test instance.	The value is an integer ranging from 1 to 4294967295.

Parameter

Description

Value

upper-limit upper-limit

Configures an upper alarm threshold for the near-end frame loss ratio of proactive LSM.

The value is a string of 1 to 8 case-insensitive characters, spaces not supported.

lower-limit lower-limit

Configures a lower alarm threshold for the near-end frame loss ratio of proactive SLM.

The value is a string of 1 to 8 case-insensitive characters, spaces not supported. The lower alarm threshold must be less than the upper alarm threshold.

test-id test-id-value

Specifies the ID of a test instance.

The value is an integer ranging from 1 to 4294967295.

Views

MA view

Default Level

2: Configuration level

Task Name and Operations

Task Name	Operations
y1731	write

Usage Guidelines

Usage Scenario

Ethernet frame loss measurement (ETH-LM) enables a local MEP and its RMEP to exchange ETH-LM frames to collect frame loss statistics on E2E links. ETH-LM modes are classified into near-end ETH-LM and far-end ETH-LM. Near-end ETH-LM applies to an inbound interface, and far-end ETH-LM applies to an outbound interface on a MEP. ETH-LM counts the number of errored frame seconds to determine the duration when a link is unavailable.

To set the upper and lower threshold for the near-end packet loss rate in SLM, run the loss-measure single-ended-synthetic local-ratio-threshold command. If the near-end packet loss rate exceeds the upper threshold or is lower than the lower threshold, the number of threshold-crossing events is counted. The display y1731 period-data command displays the number of threshold-crossing times.

Prerequisites

The cfm md command has been run to configure an MD. The ma command has been run to configure an MA. The mep mep-id command has been run to configure MEPs.

Example

# Set lower and upper alarm thresholds for the near-end frame loss ratio of proactive SLM to 60.1150% and 72.4%, respectively.

<HUAWEI> system-view
[~HUAWEI] mpls
[*HUAWEI-mpls] quit
[*HUAWEI] mpls l2vpn
[*HUAWEI-l2vpn] quit
[*HUAWEI] interface GigabitEthernet 0/1/1
[*HUAWEI-GigabitEthernet0/1/1] undo shutdown
[*HUAWEI-GigabitEthernet0/1/1] mpls l2vc 2.2.2.2 100
[*HUAWEI-GigabitEthernet0/1/1] quit
[*HUAWEI] cfm enable
[*HUAWEI] cfm md md1
[*HUAWEI-md-md1] ma ma1
[*HUAWEI-md-md1-ma-ma1] map mpls l2vc 2.2.2.2 100 raw
[*HUAWEI-md-md1-ma-ma1] mep mep-id 1 interface GigabitEthernet0/1/1 inward
[*HUAWEI-md-md1-ma-ma1] test-id 1 mep 1 mac 00e0-fc12-7890
[*HUAWEI-md-md1-ma-ma1] loss-measure single-ended-synthetic local-ratio-threshold test-id 1 upper-limit 72.4 lower-limit 60.1150