L2VPN/2/hwRemoteApPwParaMisMatch_active

Message

L2VPN/2/hwRemoteApPwParaMisMatch_active: The low-speed interface parameter settings reported by the remoter AP mismatch those of the PW.(VcId =[VcId], VcType=[VcType], PeerAddress=[PeerAddress], EncapNum=[EncapNum], JitterBuffer=[JitterBuffer], RtpHeader=[RtpHeader], IdleCode=[IdleCode], InterfaceIndex=[RemoteIfIndex], InterfaceName=[RemoteIfName], RemotePhyType=[RemotePhyType], RemoteLinkType=[RemoteLinkType], RemoteEncap=[RemoteEncap], RemoteMinEncapNum=[RemoteMinEncapNum], RemoteMaxEncapNum=[RemoteMaxEncapNum], RemoteEncapStep=[RemoteEncapStep], RemoteMinJitterBuffer=[RemoteMinJitterBuffer], RemoteMaxJitterBuffer=[RemoteMaxJitterBuffer], RemoteJitterBufferStep=[RemoteJitterBufferStep], RemoteTtpHeader=[RemoteTtpHeader], RemoteMinIdleCode=[RemoteMinIdleCode], RemoteMaxIdleCode=[RemoteMaxIdleCode])

Description

An alarm was generated because the PW parameter settings on the remote AP mismatched those on the aggregation side.

Parameters

Parameter Name	Parameter Meaning
VcId	VC ID of the PW
VcType	Encapsulation type supported by the Remote-AP interface
PeerAddress	PW peer address
EncapNum	TDM frame encapsulation number allowed by the Remote-AP interface
JitterBuffer	Jitter buffer depth for TDM frames transmitted by the Remote-AP interface
RtpHeader	RTP header carried in a TDM packet transmitted by the Remote-AP interface
IdleCode	Idle code filled when jitter buffer underflows during the transmission of TDM frames by the Remote-AP interface
RemoteIfIndex	Index of the Remote-AP interface
RemoteIfName	Name of the Remote-AP interface
RemotePhyType	Physical type of the Remote-AP interface
RemoteLinkType	Link type of the Remote-AP interface
RemoteEncap	Encapsulation type supported by the remote AC interface
RemoteMinEncapNum	Minimum TDM frame encapsulation number allowed by the remote AC interface
RemoteMaxEncapNum	Maximum TDM frame encapsulation number allowed by the remote AC interface
RemoteEncapStep	TDM frame encapsulation step length allowed by the remote AC interface
RemoteMinJitterBuffer	Minimum jitter buffer depth for TDM frames transmitted by the remote AC interface
RemoteMaxJitterBuffer	Maximum jitter buffer depth for TDM frames transmitted by the remote AC interface
RemoteJitterBufferStep	Step length for the jitter buffer depth of TDM frames transmitted by the remote AC interface
RemoteTtpHeader	RTP header carried in a TDM packet transmitted by the remote AC interface
RemoteMinIdleCode	Minimum idle code filled when jitter buffer underflows during the transmission of TDM frames by the remote AC interface
RemoteMaxIdleCode	Maximum idle code filled when jitter buffer underflows during the transmission of TDM frames by the remote AC interface

Possible Causes

The PW parameter settings on the remote AP mismatched those on the aggregation side.

Procedure

1. Check whether the TDM frame encapsulation number configured on the aggregation side is within the range reported by the remote AP and meets the specified step length requirement. Normally, the TDM frame encapsulation number is 8, 16, 32, or 40.

If the TDM frame encapsulation number is appropriate, go to 2.
If the TDM frame encapsulation number is inappropriate, go to 4.

2. Check whether the maximum jitter buffer depth configured on the aggregation side is within the range reported by the remote AP and meets the specified step length requirement. Normally, the maximum jitter buffer depth is 8, 16, 32, or 64.

If the maximum jitter buffer depth is appropriate, go to 3.
If the maximum jitter buffer depth is inappropriate, go to 4.

3. Check whether the idle code configured on the aggregation side is the same as that reported by the AP.

If they are the same, go to 5.
If they are different, go to 4.

4. Run the mpls l2vc [ instance-name instance-name ] encapsulation encapsulation-type ip-address vc-id [ [ control-word | no-control-word ] | tunnel-policy tunnel-policy-name | tdm-encapsulation-number tdm-encapsulation-number | tdm-sequence-number | jitter-buffer jitter-buffer | rtp-header | idle-code idle-code ] *command to reconfigure the TDM frame encapsulation number, maximum jitter buffer depth, or idle code on the aggregation side. Then, check whether the alarm is cleared.

If the alarm is cleared, go to 6.
If the alarm persists, go to 5.

5. Collect alarm information and configuration information, and then contact technical support personnel.

6. End.