nqaReflectorTable

1.3.6.1.4.1.2011.5.25.111.11.1.1.1

nqaReflectorID

Integer32

accessible-for-notify

This object indicates the reflector ID, which is also the index of this table.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.2

nqaReflectorIfIndex

Integer32

read-create

This object indicates the index of the reflector interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.3

nqaReflectorMacAddress

OCTET STRING{(6,6)}

read-create

This object indicates the MAC address.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.4

nqaReflectorIPAddressType

INTEGER{unknown(0),ipv4(1),ipv6(2),ipv4z(3),ipv6z(4),dns(16)}

read-write

This object indicates the type of an IP address.

The actually supported value range is 1.

1.3.6.1.4.1.2011.5.25.111.11.1.1.5

nqaReflectorIPAddress

OCTET STRING{(0,255)}

read-write

This object indicates the IP address.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.6

nqaReflectorSimulationIPAddressType

INTEGER{unknown(0),ipv4(1),ipv6(2),ipv4z(3),ipv6z(4),dns(16)}

read-write

This object indicates the type of an simulated IP address.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.7

nqaReflectorSimulationIPAddress

OCTET STRING{(0,255)}

read-write

This object indicates the simulated IP address.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.8

nqaReflectorPevid

Integer32

read-create

This object indicates the PE VLAN ID.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.9

nqaReflectorCevid

Integer32

read-create

This object indicates the CE VLAN ID.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.10

nqaReflectorAgeTime

Integer32

read-create

This object indicates the aging time, in seconds.

Setting the value to 0 indicates reserving the reflector eternally.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.11

nqaReflectorSourcePort

Integer32{(0,65535)}

read-create

This object indicates the UDP source port number. 0 means invalid UDP source port, it cannot be set but could be walked

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.12

nqaReflectorDestinationPort

Integer32{(0,65535)}

read-create

This object indicates the UDP destination port number. 0 means invalid UDP source port, it cannot be set but could be walked

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.13

nqaReflectorState

INTEGER{active(1),notinservice(2),unknown(0)}

read-only

This object indicates the status of the reflector.

1: active

2: not in service

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.14

nqaReflectorSurvivalTime

Integer32

read-only

This object indicates the survival time of the reflector, in seconds.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.15

nqaReflectorRecommendedTestMacAddress

OCTET STRING{(6,6)}

read-only

This object indicates the recommended test MAC address.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.16

nqaReflectorTestBehavior

Unsigned32{(0,3)}

read-create

This object indicates the action performed on the non-test frames by the reflector.

0: default value for 2544 reflector.

1: sharemode for 2544 reflector.

2: exclusive mode for Y.1564 reflector.

3: test flow mode for Y.1564 reflector.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.111.11.1.1.50

nqaReflectorRowStatus

INTEGER{active(1),notInService(2),notReady(3),createAndGo(4),createAndWait(5),destroy(6)}

read-create

This object indicates the status of a row, which can be created or deleted but not modified.

The value can be set to 'CreateAndGo (4)' and 'Destroy (6)'.

This object is implemented as defined in the corresponding MIB files.