S5735-S8P2X-IA200G1

Version Mapping

Table 1 lists the mapping between the S5735-S8P2X-IA200G1 chassis and software versions.

**Table 1** Version mapping
Series	Model	Software Version
S5730-S-I	S5735-S8P2X-IA200G1	V200R019C10 and later versions

Appearance and Structure

Figure 1 S5735-S8P2X-IA200G1 appearance

Figure 2 Interior of the S5735-S8P2X-IA200G1 maintenance compartment

1	Eight PoE+ 10/100/1000BASE-T ports	2	One USB port
3	Two 10GE SFP+ ports Applicable modules and cables: Industrial optical module GPON optical module Third-party GPON optical modules (Hisense LTE3415-SH+ and CIG G-97S) NOTE: If one port uses a GPON optical module, the other port cannot be used at the same time.	4	One ETH management port
5	One console port	6	Monitoring port DI: signal input line, which connects to a door status sensor. DO: signal output line, which connects to a camera alarm signal cable. NOTE: The monitoring port can be used to detect the status of a connected external device, such as the opening and closing of the maintenance compartment door. The monitoring port is used with a conductive cable. The minimum cross-sectional area of the conductor connected to a conductive cable is 0.3 mm² or 22 AWG, and the maximum cross-sectional area of the conductor is 1.3 mm² or 16 AWG. For details about how to use a monitoring port, see "Monitoring Interface Configuration" in the Configuration Guide - Device Management Configuration.
7	220 V AC power input socket	8	Fiber management tray (FMT) NOTE: The FMT is optional.
9	220 V AC power input circuit breaker NOTICE: This circuit breaker is optional. Connect an external power cable to the 220 V AC power input circuit breaker when it is in use. An external power cable needs to be prepared onsite. Ensure that the wires of the external cable are correctly connected to the L and N sockets of a plug. The circuit breaker supports a maximum of 32 A input current and provides two 220 V AC outputs. One output is connected to the AC power input socket of the switch to supply power to the switch. The other output is connected to the 220 V AC power output circuit breaker of the switch to supply power to connected PDs (such as strobe lights and non-PoE PTZ dome cameras).	10	220 V AC power output circuit breaker NOTICE: This circuit breaker is optional. The 220 V AC power output circuit breaker provides overcurrent protection only, and is only used for external power conversion. It supports a maximum of 10 A output current. The connected external devices need to provide certain surge protection capabilities. It is recommended that the surge protection capabilities for both differential and common modes be 20 kA.
11	12 V DC power output socket NOTE: The switch provides five 12 V DC outputs to external devices, such as strobe lights and non-PoE PTZ dome cameras.	12	24 V AC power output socket NOTE: The switch provides two 24 V AC outputs to external devices, such as strobe lights and non-PoE PTZ dome cameras.
13	PE cable ground terminal NOTE: It is used to ground a PE power cable for 220 V AC input or output.	14	Door status sensor NOTE: It reports an alarm when the maintenance compartment door of the switch is opened.
15	Ground screw NOTE: It is used to ground the switch. The ground cable needs to be purchased separately.	16	Cable outlet

Port Description

10/100/1000BASE-T port

A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 2 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.

**Table 2** Attributes of a 10/100/1000BASE-T Ethernet electrical port
Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3, IEEE802.3u, IEEE802.3ab
Working mode	10/100/1000 Mbit/s auto-sensing
Maximum transmission distance	100 m

10GE SFP+ port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 3 describes the attributes of a 10GE SFP+ Ethernet optical port.

**Table 3** Attributes of a 10GE SFP+ port
Attribute	Description
Connector type	LC/PC
Optical port attributes	Depend on the optical module used
Standards compliance	IEEE802.3ae
Working mode	GE/10GE auto-sensing

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4.

**Table 4** Attributes of a console port
Attribute	Description
Connector type	RJ45
Standards compliance	RS-232
Working mode	Duplex Universal Asynchronous Receiver/Transmitter (UART)
Baud rate	9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port. Table 5 describes the attributes of an ETH management port.

**Table 5** Attributes of an ETH management port
Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3
Working mode	10/100 Mbit/s auto-sensing
Maximum transmission distance	100 m

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

Figure 3 Indicators on the outside of the S5735-S8P2X-IA200G1

Figure 4 Indicators inside the maintenance compartment of the S5735-S8P2X-IA200G1
click to enlarge

**Table 6** Description of indicators
No.	Indicator	Name	Color	Status	Description
1	PWR	Power indicator	-	Steady off	The switch is powered off.
			Green	Steady on	The switch is powered on and can communicate with the built-in power module properly.
			Yellow	Steady on	The switch is powered on but cannot communicate with the built-in power module properly.
2	SYS	System status indicator	-	Steady off	The system is not running.
			Green	Fast blinking	The system is starting.
			Green	Steady on	In the system startup preparation phase, the SYS indicator is steady green for no more than 30 seconds.
			Green	Slow blinking	The system is running normally.
			Red	Steady on	The system does not work normally after registration, or a temperature alarm has been generated.
3	ALM	Alarm indicator	-	Steady off	There is no AC input or power supply is normal.
3	ALM	Alarm indicator	Red	Steady on	The power supply to the switch is abnormal.
4	USB	USB-based deployment indicator	-	Steady off	No USB flash drive is connected to the switch. The USB port is damaged. The indicator is damaged. The USB flash drive does not have any configuration file and cannot be used for deployment. The switch has been upgraded using the USB flash drive and is restarting.
			Green	Steady on	A USB-based deployment has been completed.
			Green	Blinking	The system is reading data from a USB flash drive.
			Yellow	Steady on	The switch has copied all the required files and completed the file check. The USB flash drive can be removed from the switch.
			Red	Blinking	An error has occurred when the system is executing the configuration file or reading data from the USB flash drive.
5	-	Service port indicator	Green	Steady off	The port is not connected or has been shut down.
				Steady on	The port is connected.
				Blinking	The port is sending or receiving data.
			Yellow	Steady off	The port does not supply power to any PD.
				Steady on	The port is supplying power to the connected PD.
				Blinking	The PD connected to the port is not a standard PD or its power exceeds the maximum power or power threshold of the port.
6	-	ETH port indicator	-	Steady off	The ETH port is not connected.
			Green	Steady on	The ETH port is connected.
			Green	Blinking	The port is sending or receiving data.

Power Supply Configuration

The S5735-S8P2X-IA200G1 has a built-in power module and does not support pluggable power modules. The S5735-S8P2X-IA200G1 can be directly connected to an external 220 V AC power supply and provide power for external devices. Table 7 lists the power supply configurations of the S5735-S8P2X-IA200G1.

**Table 7** Power supply configurations
Power Supply Mode	Available Power
PoE	160 W Maximum number of PoE ports (fully loaded): 802.3af (15.4 W per port): 8 802.3at (30 W per port): 5
12 V DC	Five 12 V DC outputs provide a total of 72 W power. The maximum power of a single output is 72 W.
24 V AC	Two 24 V AC outputs provide a total of 72 W power. The maximum power of a single output is 72 W.

The total maximum output power of PoE power output, five 12 V DC outputs, and two 24 V AC outputs is 160 W.

Heat Dissipation

The S5735-S8P2X-IA200G1 has no fans and uses natural heat dissipation.

Technical Specifications

Table 8 lists technical specifications of the S5735-S8P2X-IA200G1.

**Table 8** Technical specifications
Item	Description
Memory (RAM)	1 GB
Flash	512 MB in total. To view the available flash memory size, run the display version command.
Mean time between failures (MTBF)	57.28 years
Mean time to repair (MTTR)	2 hours
Availability	> 0.99999
Service port surge protection	±1.5 kV in differential mode, ±6 kV in common mode
Power supply surge protection	Surge current: AC input: 20 kA Surge: AC input: ±6 kV in differential mode; ±6 kV in common mode 12 V DC output: ±2 kV in differential mode; ±4 kV in common mode 24 V AC output: ±2 kV in differential mode; ±6 kV in common mode
Dimensions (H x W x D)	550 mm x 300 mm x 135 mm (21.65 in. x 11.81 in. x 5.31 in.)
Weight (including packaging)	12.2 kg (26.9 lb)
Stack ports	Not supported
RTC	Not supported
RPS	Not supported
PoE	Supported
Rated voltage range	220 V AC to 240 V AC, 50/60 Hz
Maximum voltage range	176 V AC to 264 V AC, 45 Hz to 66 Hz
Maximum power consumption (100% throughput)	With no output power: 34 W With output power: 209 W (device power consumption: 49 W; output power: 160 W)
Typical power consumption (30% of traffic load) Tested according to ATIS standard EEE enabled No PoE power consumption	31 W
Operating temperature	-40°C to +75°C (-40°F to 167°F) NOTE: –25ºC to +75ºC (–13ºF to +167ºF): sunshade needed; 400 LFM air velocity (minimum); GPON optical modules not supported –25ºC to +70ºC (–13ºF to +158ºF): sunshade needed; 200 LFM air velocity (minimum); GPON optical modules supported –30ºC to +60ºC (–22ºF to +140ºF): sunshade needed; 40 LFM air velocity (minimum); GPON optical modules supported –35ºC to +55ºC (–31ºF to +131ºF): sunshade needed; no requirement on the air velocity; GPON optical modules supported –35ºC to +45ºC (–31ºF to +113ºF): 1120 W/m² solar radiation (maximum); no requirement on the air velocity –40ºC to –35ºC (–40ºF to –31ºF): At least four Ethernet electrical ports must be working. When the altitude is 1800-4000 m (5906-13123 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).
Storage temperature	-40°C to +85°C (-40°F to +185°F)
IP rating	IP55
Noise under normal temperature (27°C, sound power)	Noise-free (no fans)
Relative humidity	5% to 95%, noncondensing
Operating altitude	0-4000 m (0-13123 ft.)
Product certification	EMC certification Safety certification Manufacturing certification
Part number	02312NTA-001