Example for Configuring Session-based Static Load Balancing
Session-based Static Load Balancing Overview
Load balancing can evenly distribute AP traffic loads to ensure sufficient bandwidth for each STA and to prevent a heavy load on a single AP. In static load balancing, APs are manually added to a load balancing group. When a STA wants to connect to an AP in this load balancing group, the AC uses a load balancing algorithm to determine whether to allow the STA to connect to the AP. If the connection is not allowed, the STA connects to a different AP with a lighter load.
Static load balancing can be used in scenarios such as conference rooms. For example, if two APs are deployed in a conference room, you can add the two APs to a load balancing group to prevent heavy load on a single AP.
Configuration Notes
In this example, the security policy is WPA2-PSK-CCMP. To ensure network security, choose an appropriate security policy according to your network configurations.
In tunnel forwarding mode, the management VLAN and service VLAN cannot be the same. If you set the forwarding mode to direct forwarding, you are not advised to configure the management VLAN and service VLAN to be the same.
In direct forwarding mode, configure port isolation on the interface directly connected to APs. If port isolation is not configured, many broadcast packets will be transmitted in the VLANs or WLAN users on different APs can directly communicate at Layer 2.
- Configure the management VLAN and service VLAN:
- In tunnel forwarding mode, service packets are encapsulated in a CAPWAP tunnel and forwarded to the AC. The AC then forwards the packets to the upper-layer network or APs. Service packets and management packets can be forwarded normally only if the network between the AC and APs is added to the management VLAN and the network between the AC and upper-layer network is added to the service VLAN.
- In direct forwarding mode, service packets are not encapsulated into a CAPWAP tunnel, but are directly forwarded to the upper-layer network or APs. Service packets and management packets can be forwarded normally only if the network between the AC and APs is added to the management VLAN and the network between APs and upper-layer network is added to the service VLAN.
- How to configure the source interface:
- In V200R006, run the wlan ac source interface { loopback loopback-number | vlanif vlan-id } command in the WLAN view.
- In V200R007 and V200R008, run the capwap source interface { loopback loopback-number | vlanif vlan-id } command in the system view.
- Each load balancing group supports a maximum of three APs.
- APs on which load balancing needs to be configured must be configured within the same AP region.
- A load balancing group is a set of radios, and each radio can join only one load balancing group. If dual-band APs are used, traffic is load balanced among APs working on the same frequency band. That is, a dual-band AP can join two load balancing groups.
- All APs in a load balancing group work on the same frequency band (2.4 GHz or 5 GHz). AP radios in a load balancing group must have different channels configured and work on different channels.
- No ACK mechanism is provided for multicast packet transmission on air interfaces. In addition, wireless links are unstable. To ensure stable transmission of multicast packets, they are usually sent at low rates. If a large number of such multicast packets are sent from the network side, the air interfaces may be congested. You are advised to configure multicast packet suppression to reduce impact of a large number of low-rate multicast packets on the wireless network. Exercise caution when configuring the rate limit; otherwise, the multicast services may be affected.
- In direct forwarding mode, you are advised to configure multicast packet suppression on switch interfaces connected to APs.
- In tunnel forwarding mode, you are advised to configure multicast packet suppression in traffic profiles of the AC.
- The following table lists applicable products and versions.
Table 1 Applicable products and versions Software Version
Product Model
AP Model and Version
V200R005C00
S7700, S9700
V200R005C00:
AP2010DN, AP3010DN-AGN, AP5010DN-AGN, AP5010SN-GN, AP5030DN, AP5130DN, AP6010SN-GN, AP6010DN-AGN, AP6310SN-GN, AP6510DN-AGN, AP6610DN-AGN, AP7110DN-AGN, AP7110SN-GN
V200R006C00
S5720-HI, S7700, S9700
V200R005C00:
AP2010DN, AP3010DN-AGN, AP5010DN-AGN, AP5010SN-GN, AP5030DN, AP5130DN, AP6010SN-GN, AP6010DN-AGN, AP6310SN-GN, AP6510DN-AGN, AP6610DN-AGN, AP7110DN-AGN, AP7110SN-GN
V200R007C00
S5720-HI, S7700, S9700
V200R005C10:
AP2010DN, AP3010DN-AGN, AP5010DN-AGN, AP5010SN-GN, AP5030DN, AP5130DN, AP6010SN-GN, AP6010DN-AGN, AP6310SN-GN, AP6510DN-AGN, AP6610DN-AGN, AP7110DN-AGN, AP7110SN-GN, AP8030DN, AP8130DN
V200R005C20:
AP7030DE, AP9330DN
V200R008C00
S5720-HI, S7700, S9700
V200R005C10:
AP2010DN, AP3010DN-AGN, AP5010DN-AGN, AP5010SN-GN, AP5030DN, AP5130DN, AP6010SN-GN, AP6010DN-AGN, AP6310SN-GN, AP6510DN-AGN, AP6610DN-AGN, AP7110DN-AGN, AP7110SN-GN, AP8030DN, AP8130DN
V200R005C20:
AP7030DE, AP9330DN
V200R005C30:
AP2030DN, AP4030DN, AP4130DN
For S7700, you are advised to deploy S7712 or S7706 switches for WLAN services. S7703 switches are not recommended.
For S9700, you are advised to deploy S9712 or S9706 switches for WLAN services. S9703 switches are not recommended.
Networking Requirements
As shown in Figure 1, AP1 and AP2 connect to the AC through SwitchA and join AP region 10.
When a large number of STAs access the Internet through the same AP, the AP becomes heavily loaded and WLAN service quality deteriorates. Therefore, the STAs need to be balanced on the two APs.
Data Planning
Item |
Data |
Description |
|---|---|---|
IP address of the AC's source interface |
192.168.10.1/24 |
None |
WMM profile |
Name: wmm |
None |
Radio profile |
Name: radio |
None |
Security profile |
|
None |
Traffic profile |
Name: traffic |
None |
Service set |
|
None |
DHCP server |
The AC functions as the DHCP server to assign IP addresses to APs and STAs. |
None |
AP gateway and IP address range |
VLANIF 100: 192.168.10.1/24 192.168.10.2 to 192.168.10.254/24 |
None |
STA gateway and IP address range |
VLANIF 101: 192.168.11.1/24 192.168.11.2 to 192.168.11.254/24 |
None |
MAC addresses of APs |
|
None |
Configuration Roadmap
- Configure the WLAN service so that users can connect to the Internet through the WLAN.
- Configure session-based static load balancing to prevent new STAs from associating with heavily-loaded APs.
Procedure
- Set the NAC mode to unified mode on the AC (default setting). Configure SwitchA and the AC to allow the APs and AC to transmit CAPWAP packets.
# Configure SwitchA and add interfaces GE0/0/1, GE0/0/2, and GE0/0/3 to the management VLAN 100.
[HUAWEI] sysname SwitchA [SwitchA] vlan batch 100 [SwitchA] interface gigabitethernet 0/0/1 [SwitchA-GigabitEthernet0/0/1] port link-type trunk [SwitchA-GigabitEthernet0/0/1] port trunk pvid vlan 100 [SwitchA-GigabitEthernet0/0/1] port trunk allow-pass vlan 100 [SwitchA-GigabitEthernet0/0/1] quit [SwitchA] interface gigabitethernet 0/0/2 [SwitchA-GigabitEthernet0/0/2] port link-type trunk [SwitchA-GigabitEthernet0/0/2] port trunk pvid vlan 100 [SwitchA-GigabitEthernet0/0/2] port trunk allow-pass vlan 100 [SwitchA-GigabitEthernet0/0/2] quit [SwitchA] interface gigabitethernet 0/0/3 [SwitchA-GigabitEthernet0/0/3] port link-type trunk [SwitchA-GigabitEthernet0/0/3] port trunk allow-pass vlan 100 [SwitchA-GigabitEthernet0/0/3] quit
# Add GE1/0/1 that connects the AC to SwitchA to VLAN 100.
[HUAWEI] sysname AC [AC] vlan batch 100 [AC] interface gigabitethernet 1/0/1 [AC-GigabitEthernet1/0/1] port link-type trunk [AC-GigabitEthernet1/0/1] port trunk allow-pass vlan 100 [AC-GigabitEthernet1/0/1] quit
- Configure the AC to communicate with the upstream device.
# Add the AC's uplink interface GE1/0/3 to VLAN 101.
[AC] vlan batch 101 [AC] interface gigabitethernet 1/0/3 [AC-GigabitEthernet1/0/3] port link-type trunk [AC-GigabitEthernet1/0/3] port trunk allow-pass vlan 101 [AC-GigabitEthernet1/0/3] quit
- Configure the AC as a DHCP server to assign IP addresses to STAs and APs.
# Configure a DHCP server to assign IP addresses to the APs from the IP address pool on VLANIF 100 and assign IP addresses to STAs from the IP address pool on VLANIF 101.
[AC] dhcp enable //Enable the DHCP function. [AC] interface vlanif 100 [AC-Vlanif100] ip address 192.168.10.1 24 [AC-Vlanif100] dhcp select interface //Configure an interface-based address pool. [AC-Vlanif100] quit [AC] interface vlanif 101 [AC-Vlanif101] ip address 192.168.11.1 24 [AC-Vlanif101] dhcp select interface [AC-Vlanif101] quit
- Configure AC system parameters.
# Configure the country code.
[AC] wlan ac-global country-code cn Warning: Modify the country code may delete configuration on those AP which use the global country code and reset them, continue?[Y/N]:y# Configure the AC ID and carrier ID.
[AC] wlan ac-global ac id 1 carrier id other //The default AC ID is 0. Set the AC ID to 1.# Configure the source interface.
[AC] wlan [AC-wlan-view] wlan ac source interface vlanif 100
- Manage APs on the AC.
# Check the AP type IDs after obtaining the MAC addresses of the APs.
[AC-wlan-view] display ap-type all All AP types information: ------------------------------------------------------------------------------ ID Type ------------------------------------------------------------------------------ 17 AP6010SN-GN 19 AP6010DN-AGN 21 AP6310SN-GN 23 AP6510DN-AGN 25 AP6610DN-AGN 27 AP7110SN-GN 28 AP7110DN-AGN 29 AP5010SN-GN 30 AP5010DN-AGN 31 AP3010DN-AGN 33 AP6510DN-AGN-US 34 AP6610DN-AGN-US 35 AP5030DN 36 AP5130DN 37 AP7030DE 38 AP2010DN 39 AP8130DN 40 AP8030DN 42 AP9330DN 43 AP4030DN 44 AP4130DN 45 AP3030DN 46 AP2030DN ------------------------------------------------------------------------------ Total number: 23# Set the AP authentication mode to MAC address authentication (default setting). Add the APs offline based on the AP type ID. Assume that the type of AP1 and AP2 is AP6010DN-AGN, and their MAC addresses are 60de-4476-e360 and dcd2-fc04-b500, respectively.
[AC-wlan-view] ap-auth-mode mac-auth [AC-wlan-view] ap id 1 type-id 19 mac 60de-4476-e360 [AC-wlan-ap-1] quit [AC-wlan-view] ap id 2 type-id 19 mac dcd2-fc04-b500 [AC-wlan-ap-2] quit
# Configure an AP region and add the APs to the AP region.
[AC-wlan-view] ap-region id 10 //Create AP region 10. [AC-wlan-ap-region-10] quit [AC-wlan-view] ap id 1 [AC-wlan-ap-1] region-id 10 //Add APs to region 10. [AC-wlan-ap-1] quit [AC-wlan-view] ap id 2 [AC-wlan-ap-2] region-id 10 [AC-wlan-ap-2] quit
# Power on AP1 and AP2 and run the display ap all command on the AC to check the AP state. The command output shows that the APs are in normal state.
[AC-wlan-view] display ap all All AP information: Normal[2],Fault[0],Commit-failed[0],Committing[0],Config[0],Download[0] Config-failed[0],Standby[0],Type-not-match[0],Ver-mismatch[0] ------------------------------------------------------------------------------ AP AP AP Profile AP AP /Region ID Type MAC ID State Sysname ------------------------------------------------------------------------------ 1 AP6010DN-AGN 60de-4476-e360 0/10 normal ap-1 2 AP6010DN-AGN dcd2-fc04-b500 0/10 normal ap-2 ------------------------------------------------------------------------------ Total number: 2,printed: 2
- Configure WLAN service parameters.
# Create a WMM profile named wmm and retain the default settings in the profile.
[AC-wlan-view] wmm-profile name wmm id 1 [AC-wlan-wmm-prof-wmm] quit
# Create a radio profile named radio and bind the WMM profile wmm to the radio profile. Set the channel mode to fixed.
[AC-wlan-view] radio-profile name radio id 1 [AC-wlan-radio-prof-radio] channel-mode fixed //Set the channel mode fixed. The default value is auto. [AC-wlan-radio-prof-radio] wmm-profile name wmm [AC-wlan-radio-prof-radio] quit [AC-wlan-view] quit# Create WLAN-ESS interface 1.
[AC] interface wlan-ess 1 [AC-Wlan-Ess1] port trunk allow-pass vlan 101 [AC-Wlan-Ess1] quit
# Create a security profile named security.
[AC] wlan [AC-wlan-view] security-profile name security id 1 [AC-wlan-sec-prof-security] security-policy wpa2 //Configure security policy WPA2. [AC-wlan-sec-prof-security] wpa2 authentication-method psk pass-phrase cipher huawei123 encryption-method ccmp //Set the encryption method to PSK+CCMP. [AC-wlan-sec-prof-security] quit
# Create a traffic profile named traffic and retain the default settings in the profile.
[AC-wlan-view] traffic-profile name traffic id 1 [AC-wlan-traffic-prof-traffic] quit
# Create a service set named test and bind the WLAN-ESS interface, security profile, and traffic profile to the service set.
[AC-wlan-view] service-set name test id 1 [AC-wlan-service-set-test] ssid test //Name the SSID test. [AC-wlan-service-set-test] wlan-ess 1 [AC-wlan-service-set-test] security-profile name security [AC-wlan-service-set-test] traffic-profile name traffic [AC-wlan-service-set-test] service-vlan 101 //Set the VLAN ID of the service set to 101. The default value is 1. [AC-wlan-service-set-test] forward-mode tunnel //Set the service forwarding mode to tunnel forwarding. [AC-wlan-service-set-test] quit
- Configure VAPs and deliver VAP parameters to APs.
# Configure VAPs.
[AC-wlan-view] ap 1 radio 0 [AC-wlan-radio-1/0] radio-profile name radio //Bind the radio profile to a radio. [AC-wlan-radio-1/0] channel 20mhz 11 //Set the working channel of the radio to 11 and the channel bandwidth to 20 MHz. [AC-wlan-radio-1/0] service-set name test //Bind the service set to the radio. [AC-wlan-radio-1/0] quit [AC-wlan-view] ap 2 radio 0 [AC-wlan-radio-2/0] radio-profile name radio [AC-wlan-radio-2/0] channel 20mhz 6 [AC-wlan-radio-2/0] service-set name test [AC-wlan-radio-2/0] quit
- Configure a load balancing group, add AP1 and AP2 to the load balancing group, and set the load balancing mode of the group to session-based load balancing.
[AC-wlan-view] load-balance-group name huawei //Create load balancing group huawei. [AC-wlan-load-group-huawei] member ap-id 1 radio-id 0 //Add AP1 radio 0 to load balancing group huawei. [AC-wlan-load-group-huawei] member ap-id 2 radio-id 0 [AC-wlan-load-group-huawei] session gap 5 //Configure session-based static load balancing and set the load difference threshold to 5%. The default value is 4%. [AC-wlan-load-group-huawei] associate-threshold 10 //Set the maximum number of association requests in a static load balancing group to 10. The default value is 6. [AC-wlan-load-group-huawei] quit [AC-wlan-view] commit ap 1 //Commit configurations. Warning: Committing configuration may cause service interruption, continue?[Y/N]y [AC-wlan-view] commit ap 2 Warning: Committing configuration may cause service interruption, continue?[Y/N]y
- Verify the configuration.
- After the preceding configuration is complete, STAs can discover the WLAN with SSID test.
- When a new STA requests to access the Internet through an AP, the AC uses a static load balancing algorithm to determine whether to allow access from the STA. If the requested AP has more than 5% greater load than the other AP, the AC rejects the association request of the STA. If the STA continues to send more than 10 association requests to the AP, the AC allows the STA to associate with the AP.
Configuration Files
SwitchA configuration file
# sysname SwitchA # vlan batch 100 # interface GigabitEthernet0/0/1 port link-type trunk port trunk pvid vlan 100 port trunk allow-pass vlan 100 # interface GigabitEthernet0/0/2 port link-type trunk port trunk pvid vlan 100 port trunk allow-pass vlan 100 # interface GigabitEthernet0/0/3 port link-type trunk port trunk allow-pass vlan 100 # return
AC configuration file
# sysname AC # vlan batch 100 to 101 # wlan ac-global carrier id other ac id 1 # dhcp enable # interface Vlanif100 ip address 192.168.10.1 255.255.255.0 dhcp select interface # interface Vlanif101 ip address 192.168.11.1 255.255.255.0 dhcp select interface # interface GigabitEthernet1/0/1 port link-type trunk port trunk allow-pass vlan 100 # interface GigabitEthernet1/0/3 port link-type trunk port trunk allow-pass vlan 101 # interface Wlan-Ess1 port trunk allow-pass vlan 101 # wlan wlan ac source interface vlanif100 ap-region id 10 ap id 1 type-id 19 mac 60de-4476-e360 sn 210235419610CB002287 region-id 10 ap id 2 type-id 19 mac dcd2-fc04-b500 sn 210235555310CC000094 region-id 10 wmm-profile name wmm id 1 traffic-profile name traffic id 1 security-profile name security id 1 service-set name test id 1 forward-mode tunnel wlan-ess 1 ssid test traffic-profile id 1 security-profile id 1 service-vlan 101 radio-profile name radio id 1 channel-mode fixed wmm-profile id 1 ap 1 radio 0 radio-profile id 1 channel 20MHz 11 service-set id 1 wlan 1 ap 2 radio 0 radio-profile id 1 channel 20MHz 6 service-set id 1 wlan 1 load-balance-group name huawei id 0 associate-threshold 10 session gap 5 member ap-id 1 radio-id 0 member ap-id 2 radio-id 0 # return