EOAM1AG_1.3.6.1.4.1.2011.5.25.136.1.6.46 hwDot1agCfmRDI

Description

EOAM1AG/3/RDI: OID [oid] MEP received a CCM with RDI flag set. (MdIndex=[GAUGE], MaIndex=[GAUGE], MdName=[STRING], MaName=[STRING], MepId=[INTEGER], RmepId=[INTEGER])

The RMEP sent a CCM carrying the RDI flag with the value of 1 to the MEP.

Attribute

Alarm ID	Alarm Severity	Alarm Type
1.3.6.1.4.1.2011.5.25.136.1.6.46	Minor	communicationsAlarm(2)

Parameters

Name	Meaning
oid	Indicates the MIB object ID of the alarm.
MdIndex	Index of an MD table
MaIndex	Index of an MA table
MdName	Name of an MD
MaName	Name of an MA
MepId	ID of a MEP
RmepId	ID of an RMEP

Impact on the System

System performance will not be affected.

Possible Causes

Cause 1: If an RMEP received a non-RDI trap, the RMEP set the RDI flag to 1 in a CCM and sent the CCM to the MEP.

Cause 2: If CFM association was enabled and an associated interface or protocol notified the RMEP of a detected fault, the RMEP set the RDI flag to 1 in a CCM and sent the CCM to the MEP.

Procedure

Run the display cfm remote-mep [ md md-name ma ma-name mep-id mep-id ] command on the RMEP to view the value of the Alarm Status field.
- If the value of the Alarm Status field is none, go to Step 3.
- If the value of the Alarm Status field is not none, go to Step 2.
Perform the following steps on the RMEP:
- If the value of the Alarm Status field is LOC, follow the troubleshooting procedure described in EOAM1AG_1.3.6.1.4.1.2011.5.25.136.1.6.42 hwDot1agCfmLOC to rectify the fault. Check whether the trap is cleared. If the trap persists, go to Step 3.
- If the value of the Alarm Status field is unexpectedMAC, follow the troubleshooting procedure described in EOAM1AG_1.3.6.1.4.1.2011.5.25.136.1.6.40 hwDot1agCfmUnexpectedMAC to rectify the fault. Check whether the trap is cleared. If the trap persists, go to Step 3.
- If the value of the Alarm Status field is unexpectedPeriod, follow the troubleshooting procedure described in EOAM1AG_1.3.6.1.4.1.2011.5.25.136.1.6.38 hwDot1agCfmUnexpectedPeriod to rectify the fault. Check whether the trap is cleared. If the trap persists, go to Step 3.
- If the value of the Alarm Status field is unexpectedMEP, follow the troubleshooting procedure described in EOAM1AG_1.3.6.1.4.1.2011.5.25.136.1.6.36 hwDot1agCfmUnexpectedMEP to rectify the fault. Check whether the trap is cleared. If the trap persists, go to Step 3.
- If the value of the Alarm Status field is mismerge, follow the troubleshooting procedure described in EOAM1AG_1.3.6.1.4.1.2011.5.25.136.1.6.34 hwDot1agCfmMismerge to rectify the fault. Check whether the trap is cleared. If the trap persists, go to Step 3.
Perform the following steps on the RMEP:
1. Run the oam-mgr command to enter the MGR view.
2. Run the display this command. Check whether CFM is associated with an interface or a protocol. If there is no association configuration, go to 4.
3. If CFM is associated with an interface or a protocol, check whether the associated interface or protocol fails. If the associated interface or protocol works properly, go to Step 4. If the associated interface or protocol fails, rectify the fault. Check whether the trap is cleared. If the trap persists, go to Step 4.
Collect alarm information and configuration information, and then contact technical support personnel.