S5720-56C-PWR-HI-AC

Version Mapping

Table 1 lists the mapping between the S5720-56C-PWR-HI-AC chassis and software versions.

**Table 1** Version mapping
Series	Model	Software Version
S5720-HI	S5720-56C-PWR-HI-AC	V200R006C00 and later versions

Appearance and Structure

Figure 1 S5720-56C-PWR-HI-AC appearance

1	Forty-eight PoE+ 10/100/1000BASE-T ports	2	Four 10GE SFP+ ports Applicable modules and cables: GE optical module GE-CWDM optical module GE-DWDM optical module GE copper module 10GE SFP+ optical module (OSXD22N00 not supported) 10GE-CWDM optical module 10GE-DWDM optical module (applicable in V200R009C00 and later versions) 1 m, 3 m, and 10 m SFP+ high-speed copper cables 5 m SFP+ high-speed copper cable (applicable in V200R009C00 and later versions) 3 m and 10 m AOC cables 0.5 m and 1.5 m SFP+ dedicated stack copper cables (used for zero-configuration stacking, supported in V200R011C10 and later versions)
3	One ETH management port	4	One mini USB port
5	One console port	6	One USB port
7	Ground screw NOTE: It is used with a ground cable.	8	ESN label NOTE: You can draw it out to view the ESN and MAC address of the switch.
9	Rear card slot 1 NOTE: This slot is reserved for future use.	10	Rear card slot 2 NOTE: Card supported: ES5D21X04S01 (4-Port 10 GE SFP+ Rear Interface Card)
11	Power module slot 2 NOTE: Applicable power module: 1150 W AC PoE power module	12	Power module slot 1 NOTE: Applicable power module: 1150 W AC PoE power module

Port Description

10/100/1000BASE-T port

A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 2 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.

**Table 2** Attributes of a 10/100/1000BASE-T Ethernet electrical port
Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3, IEEE802.3u, IEEE802.3ab
Working mode	10/100/1000 Mbit/s auto-sensing
Maximum transmission distance	100 m

10GE SFP+ port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 3 describes the attributes of a 10GE SFP+ Ethernet optical port.

**Table 3** Attributes of a 10GE SFP+ port
Attribute	Description
Connector type	LC/PC
Optical port attributes	Depend on the optical module used
Standards compliance	IEEE802.3ae
Working mode	GE/10GE auto-sensing

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4.

**Table 4** Attributes of a console port
Attribute	Description
Connector type	RJ45
Standards compliance	RS-232
Working mode	Duplex Universal Asynchronous Receiver/Transmitter (UART)
Baud rate	9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s Default value: 9600 bit/s

Mini USB port

The mini USB port is connected to a console for on-site configuration. When both the Mini USB and console port have a cable connected, only the Mini USB port works.

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port. Table 5 describes the attributes of an ETH management port.

**Table 5** Attributes of an ETH management port
Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3
Working mode	10/100 Mbit/s auto-sensing
Maximum transmission distance	100 m

In V200R012C00 and later versions, you can log in to the switch that contains the ETH management port for the first time through the ETH port. For details, see "First Login to a Switch" in the Configuration Guide - Basic Configuration. If you have logged in to the device for the first time by pressing and holding the MODE button for 6 seconds or longer and saved the configuration, the default configuration on the ETH port will be cleared. In this case, you cannot log in to the switch for the first time through the ETH port. You are advised to log in to the switch for the first time through the ETH port.

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

In V200R007 and later versions, you can hold down the mode switch button for 6s and release it to start the web initial login mode. Either of the following situations will occur:

If the switch has no configuration file, the system attempts to enter the web initial login mode. In this mode, the status of mode indicators is as follows:
- If the system enters the web initial login mode successfully, all mode indicators turn green and stay on for a maximum of 10 minutes.
- If the system fails to enter the initial login mode, all mode indicators fast blink for 10 seconds and then restore to the default status.
If the switch has a configuration file, the system cannot enter the web initial login mode. In this case, all mode indicators fast blink for 10s, and then return to the default states.

Figure 2 Indicators on the S5720-56C-PWR-HI-AC

**Table 6** Description of indicators on the switch
No.	Indicator	Name	Color	Status	Description
1	PWR1	Power module indicator	-	Off	No power module is available in power module slot 1, or the switch has only one power module but the power module does not work normally.
			Green	Steady on	A power module is installed in power module slot 1 and is working normally.
			Yellow	Steady on	The switch has two power modules installed. Any of the following situations occurs in power module slot 1: A power module is available in this slot but its power switch is in the OFF position. A power module is available in this slot but it is not connected to a power source. The power module in this slot has failed.
2	PWR2	Power module indicator	-	Off	No power module is available in power module slot 2, or the switch has only one power module but the power module does not work normally.
			Green	Steady on	A power module is installed in power module slot 2 and is working normally.
			Yellow	Steady on	The switch has two power modules installed. Any of the following situations occurs in power module slot 2: A power module is available in this slot but its power switch is in the OFF position. A power module is available in this slot but it is not connected to a power source. The power module in this slot has failed.
3	SYS	System status indicator	-	Off	The system is not running.
			Green	Fast blinking	The system is starting.
			Green	Slow blinking	The system is running normally.
			Red	Steady on	The system does not work normally after registration, or a fan alarm or temperature alarm has been generated.
4	STAT	Status indicator	-	Off	The status mode is not selected.
4	STAT	Status indicator	Green	Steady on	The status mode (default mode) is selected. If the status mode is selected, the service port indicator shows the port link or activity state.
5	SPED	Speed indicator	-	Off	The speed mode is not selected.
5	SPED	Speed indicator	Green	Steady on	The service port indicators show the port speeds. After 45 seconds, the service port indicators automatically restore to the status mode.
6	STCK	Stack indicator	-	Off	If you are not changing the indicator mode (default): The switch is in stack standby or slave state or the stacking function is not enabled on the switch. If you are changing the indicator mode: The stack mode is not selected.
			Green	Steady on	The switch is a standby or slave switch in a stack, and the service port indicators show the stack ID of the switch.
			Green	Blinking	If you are not changing the indicator mode (default): The switch is a stack master switch or a standalone switch with the stacking function enabled. If you are changing the indicator mode: The switch is the master switch in a stack or a standalone switch, and the service port indicators show the stack ID of the master switch. After 45 seconds, the service port indicators automatically restore to the status mode.
7	PoE	PoE indicator	-	Off	The PoE mode is not selected.
7	PoE	PoE indicator	Green	Steady on	The service port indicators show the PoE status. After 45 seconds, the service port indicators automatically restore to the status mode.
8	MODE	Mode switch button	-	-	When you press this button once, the service port indicators change to the speed mode and show the speed of each service port When you press this button a second time, the service port indicators change to the stack mode and show the stack ID of the local switch. When you press this button a third time, the service port indicators change to the PoE mode and show the PoE status of each service port. When you press this button a fourth time, the service port indicators restore to the default mode, and the STAT indicator turns green. If you do not press the MODE button within 45 seconds, the service port indicators restore to the default mode. In this case, the STAT indicator is steady green, the SPED and PoE indicators are off, and the STCK indicator is off or blinking green.
9	-	Service port indicator	Meanings of service port indicators vary in different modes. For details, see Table 7.
10	-	Mini USB indicator	-	Off	The Mini USB port is disabled, and the console port is enabled.
10	-	Mini USB indicator	Green	Steady on	The Mini USB port is enabled. When the Mini USB indicator is steady green, the console indicator is off.
11	-	Console indicator	-	Off	The console port is disabled, and the Mini USB port is enabled.
11	-	Console indicator	Green	Steady on	The console port is enabled (default state). When the console indicator is steady green, the Mini USB indicator is off.
12	-	ETH port indicator	-	Off	The ETH port is not connected.
			Green	Steady on	The ETH port is connected.
			Green	Blinking	The ETH port is sending or receiving data.
13	-	USB-based deployment indicator	-	Off	No USB flash drive is connected to the switch. The USB port is damaged. The indicator is damaged. The USB flash drive does not have any configuration file and cannot be used for deployment. The switch has been upgraded using the USB flash drive and is restarting.
			Green	Steady on	A USB-based deployment has been completed.
			Green	Blinking	The system is reading data from the USB flash drive.
			Yellow	Steady on	The switch has copied all the required files and completed the file check. The USB flash drive can be removed from the switch.
			Red	Blinking	An error has occurred when the system is executing the configuration file or reading data from the USB flash drive.

**Table 7** Description of service port indicators in different modes
Display Mode	Color	Description
Status	Green	Off: The port is not connected or has been shut down. Steady on: The port is connected. Blinking: The port is sending or receiving data.
Speed	Green	Off: The port is not connected or has been shut down. Steady on: 10M/100M/1000M port: The port is operating at 10/100 Mbit/s. 1000M/10GE port: The port is operating at 1000 Mbit/s. Blinking: 10M/100M/1000M port: The port is operating at 1000 Mbit/s. 1000M/10GE port: The port is operating at 10 Gbit/s.
PoE	Green	Off: The port does not provide PoE power. Steady on: The port is providing PoE power. Blinking: The PD connected to the port is not a standard PD or its power exceeds the maximum power or power threshold of the port.
Stack	Green	Off: The STCK mode is not selected. If the indicator is steady on, the switch is not a master switch: If the indicator of a port is steady on, the number of this port is the stack ID of the switch. If the indicators of ports 1 to 9 are steady on, the stack ID of the switch is 0. If the indicator is blinking, the switch is a master switch: If the indicator of a port is blinking, the number of this port is the stack ID of the switch. If the indicators of ports 1 to 9 are blinking, the stack ID of the switch is 0.

Power Supply Configuration

The S5720-56C-PWR-HI-AC is a PoE switch and uses 1150 W AC PoE power modules. It has two power module slots. Table 8 lists its power supply configurations.

**Table 8** Power supply configurations
Power Module 1	Power Module 2	Available PoE Power	Maximum Number of Ports (Fully Loaded)
1150 W (220 V)	-	785.4 W	802.3af (15.4 W per port): 48 802.3at (30 W per port): 26
1150 W (220 V)	1150 W (220 V)	1440 W	802.3af (15.4 W per port): 48 802.3at (30 W per port): 48
1150 W (110 V)	-	446.6 W	802.3af (15.4 W per port): 29 802.3at (30 W per port): 14
1150 W (110 V)	1150 W (110 V)	893.2 W	802.3af (15.4 W per port): 48 802.3at (30 W per port): 29

When a switch has two power modules installed, the two power modules work in redundancy mode to provide power for the chassis and in load balancing mode to provide power for PDs.

Figure 3 shows the power supply mode of dual AC PoE power modules (PWR1 and PWR2). After AC power is transmitted to the PWR modules, the PWR modules provide 12 V and -53 V outputs. The outputs are combined on the motherboard, which then provides 12 V voltage for the switch and -53 V voltage for the PDs.

Figure 3 Power supply by dual AC PoE power modules

L: live wire

N: neutral wire

PGND: protection ground wire

GND: 12 V reference ground

RTN: -53 V reference ground

Heat Dissipation

The S5720-56C-PWR-HI-AC has five built-in fans for forced air cooling. The airflow direction is left-to-right.

Technical Specifications

Table 9 lists technical specifications of the S5720-56C-PWR-HI-AC.

**Table 9** Technical specifications
Item	Description
Memory (RAM)	4 GB
Flash	512 MB in total. To view the available flash memory size, run the display version command.
Mean time between failures (MTBF)	39.31 years when no interface card is configured; 37.53 years when a 4-port 10GE interface card is configured
Mean time to repair (MTTR)	2 hours
Availability	> 0.99999
Service port surge protection	Common mode: ±1 kV
Power supply surge protection	±2 kV in differential mode, ±4 kV in common mode
Dimensions (H x W x D)	44.4 mm x 442.0 mm x 420.0 mm (1.75 in. x 17.4 in. x 16.5 in.) When 1150 W power modules are installed, they stretch out from the chassis. Therefore, the total depth of the switch changes to 507.3 mm (19.97 in.).
Weight (with packaging)	10.9 kg (24.03 lb)
Stack ports	Four fixed 10GE SFP+ ports on the front panel or ports on the 4-port 10GE SFP+ rear interface card NOTE: The switch supports service port stacking since V200R009C00.
RTC	Supported
RPS	Not supported
PoE	Supported
Rated voltage range	100 V AC to 240 V AC, 50/60 Hz
Maximum voltage range	90 V AC to 264 V AC, 47 Hz to 63 Hz
Maximum power consumption (100% throughput, 100% PoE loads, full speed of fans)	1739 W (system power consumption: 299 W, PoE: 1440 W)
Typical power consumption (30% of traffic load) Tested according to ATIS standard EEE enabled No PoE power consumption	132.35 W
Operating temperature	0°C to 45°C (32°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.) NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).
Short-term operating temperature	-5°C to +50°C (23°F to 122°F) at an altitude of 0-1800 m (0-5906 ft.) NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.). The equipment can operate beyond the normal operating temperature range for a short-term period, but the following conditions must be met: The equipment operates at a temperature of over 45°C (113°F) consecutively for at most 96 hours in one year. The equipment operates at a temperature of over 45°C (113°F) for a total of no more than 360 hours in one year. The equipment operates at a temperature of over 45°C (113°F) for no more in 15 times in one year. The equipment may be damaged or experience unexpected exceptions if any of the preceding limits is exceeded. The equipment cannot start when the temperature is lower than 0°C (32°F). The maximum distance of optical modules used in these conditions cannot exceed 10 km.
Storage temperature	-40°C to +70°C (-40°F to +158°F)
Noise under normal temperature (27°C, sound power)	< 69.8 dB(A)
Relative humidity	5% to 95%, noncondensing
Operating altitude	0-5000 m (0-16404 ft.)
Certification	EMC certification Safety certification Manufacturing certification
Part number	02358599