S5720-52X-PWR-LI-ACF

Version Mapping

Table 1 lists the mapping between the S5720-52X-PWR-LI-ACF chassis and software versions.

**Table 1** Version mapping
Series	Model	Software Version
S5720-LI	S5720-52X-PWR-LI-ACF	V200R011C10 and later versions

Appearance and Structure

Figure 1 S5720-52X-PWR-LI-ACF appearance

1	Forty-eight PoE+ 10/100/1000BASE-T ports	2	Four 10GE SFP+ ports Applicable modules and cables: GE optical module GE-CWDM optical module GE-DWDM optical module GE copper module (only 1000 Mbit/s supported) 10GE SFP+ optical module (OSXD22N00 not supported) 10GE-CWDM optical module 10GE-DWDM optical module 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables 3 m and 10 m AOC cables 0.5 m and 1.5 m SFP+ dedicated stack copper cables (used for zero-configuration stacking, supported in V200R011C10 and later versions) H87MMA5671A2 GPON optical module (applicable in V200R012C00 and later versions) NOTE: If a port uses a GPON optical module, other 10GE SFP+ optical ports cannot be used.
3	One PNP button NOTICE: Applicable in V200R012C00 and later versions: To restore the factory settings and reset the switch, hold down the button for at least 6 seconds. To reset the switch, press the button. Resetting the switch will cause service interruption. Exercise caution when you press the PNP button.	4	One console port
5	One USB port	6	Ground screw NOTE: It is used with a ground cable.
7	RPS socket NOTE: It is used with an RPS cable, which is not hot swappable.	8	Jack for AC power cable locking strap NOTE: The AC power cable locking strap is not delivered with the switch.
9	AC socket NOTE: It is used with an AC power cable.	-	-

Interface Description

10/100/1000BASE-T port

A 10/100/1000BASE-T Ethernet electrical port sends and receives service data at 10/100/1000 Mbit/s, and must use an Ethernet cable. Table 2 describes the attributes of a 10/100/1000BASE-T Ethernet electrical port.

**Table 2** Attributes of a 10/100/1000BASE-T Ethernet electrical port
Attribute	Description
Connector type	RJ45
Standards compliance	IEEE802.3, IEEE802.3u, IEEE802.3ab
Working mode	10/100/1000 Mbit/s auto-sensing
Maximum transmission distance	100 m

10GE SFP+ port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 3 describes the attributes of a 10GE SFP+ Ethernet optical port.

**Table 3** Attributes of a 10GE SFP+ port
Attribute	Description
Connector type	LC/PC
Optical port attributes	Depend on the optical module used
Standards compliance	IEEE802.3ae
Working mode	GE/10GE auto-sensing

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4.

**Table 4** Attributes of a console port
Attribute	Description
Connector type	RJ45
Standards compliance	RS-232
Working mode	Duplex Universal Asynchronous Receiver/Transmitter (UART)
Baud rate	9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s Default value: 9600 bit/s

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

Indicator Description

The S5720-52X-PWR-LI-ACF has the same types of indicators as the S5720-28X-PWR-LI-AC. For details, see Indicator Description.

Power Supply Configuration

The S5720-52X-PWR-LI-ACF has a built-in power module and does not support pluggable power modules. The built-in power module can provide 740 W PoE power, which ensures full PoE power on 48 ports in compliance with 802.3af or on 24 ports in compliance with 802.3at. The switch can connect to an RPS1800 power supply. The RPS1800 only provides system power redundancy and does not increase the PoE capacity of the switch.

Figure 2 shows the power supply mode of a built-in AC PoE power module (PWR). The PWR module receives AC power from an external power source and provides two outputs: 12 V and -53 V. The 12 V output is provided for the chassis, and the -53 V output is provided for PDs.

Figure 2 Power supply by a built-in AC PoE power module

L: live wire

N: neutral wire

PGND: protection ground wire

GND: 12 V reference ground

RTN: -53 V reference ground

Heat Dissipation

The S5720-52X-PWR-LI-ACF have two built-in fans for forced air cooling. The airflow direction is left-to-right.

This figure only shows the airflow direction and does not depict the actual device.

Technical Specifications

Table 5 lists technical specifications of the S5720-52X-PWR-LI-ACF.

**Table 5** Technical specifications
Item	Description
Memory (RAM)	512 MB
Flash	512 MB in total. To view the available flash memory size, run the display version command.
Mean time between failures (MTBF)	45 years
Mean time to repair (MTTR)	2 hours
Availability	> 0.99999
Service port surge protection	Common mode: ±7 kV
Power supply surge protection	±6 kV in differential mode, ±6 kV in common mode
Dimensions (H x W x D)	43.6 mm x 442.0 mm x 310.0 mm (1.72 in. x 17.4 in. x 12.2 in.)
Weight (with packaging)	6.6 kg (14.55 lb)
Stack ports	Forty-eight 10/100/1000BASE-T ports and four 10G SFP+ ports
RTC	Not supported
RPS	Supported
PoE	Supported
Rated voltage range	100 V AC to 240 V AC, 50/60 Hz
Maximum voltage range	90 V AC to 264 V AC, 47 Hz to 63 Hz
Maximum power consumption (100% throughput, full speed of fans)	Not providing the PoE function: 52.1 W 100% PoE loads: 977 W (system power consumption: 237.8 W, PoE: 739.2 W)
Typical power consumption (30% of traffic load) Tested according to ATIS standard EEE enabled No PoE power consumption	42.9 W
Operating temperature	0°C to 45°C (32°F to 113°F) at an altitude of 0-1800 m (0-5906 ft.) NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.).
Short-term operating temperature	-5°C to +55°C (23°F to 131°F) at an altitude of 0-1800 m (0-5906 ft.) NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1°C (1.8°F) every time the altitude increases by 220 m (722 ft.). The equipment can operate beyond the normal operating temperature range for a short-term period, but the following conditions must be met: The equipment operates at a temperature of over 45°C (113°F) consecutively for at most 96 hours in one year. The equipment operates at a temperature of over 45°C (113°F) for a total of no more than 360 hours in one year. The equipment operates at a temperature of over 45°C (113°F) for no more in 15 times in one year. The equipment may be damaged or experience unexpected exceptions if any of the preceding limits is exceeded. The equipment cannot start when the temperature is lower than 0°C (32°F). The maximum distance of optical modules used in these conditions cannot exceed 10 km.
Storage temperature	-40°C to +70°C (-40°F to +158°F)
Noise under normal temperature (27°C, sound power)	< 53.9 dB(A)
Relative humidity	5% to 95%, noncondensing
Operating altitude	0-5000 m (0-16404 ft.)
Certification	EMC certification Safety certification Manufacturing certification
Part number	98010621